The relationship of bonding strength and temperature are investigated.
分析了键合强度与键合温度之间的关系。
The effects of dosage of each material on the bonding strength were studied.
研究了原材料的用量变化对胶粘剂粘接强度的影响。
The conclusion which the bonding strength is obviously influenced by the interlaced yarns.
得出空气变形丝对涂层织物的剥离强度具有显著影响的结论。
The properties of fired paste and the viscosity strongly affect diffusion bonding strength.
浆料的烧成特性和粘度对扩散连接强度影响较大。
At last, the approach of increasing bonding strength and decreasing shearing stress is presented.
最后，给出提高新老混凝土界面粘结强度和降低粘结面剪应力的方法。
Objective To compare the bonding strength of two kinds of bonding adhesion in two different models.
目的比较两种粘结剂在两种建模方式下对粘结强度的影响。
The influences of ultrasonic power on heavy aluminum wire wedge bonding strength were investigated.
超声功率是影响粗铝丝引线键合强度的最主要因素之一。
The bonding strength of the new adhesive completely meets the requirements of orthodontic adhesives.
这种新型粘合剂的粘接强度完全满足了正畸粘合剂的要求。
The formulation, physical properties and bonding strength of Adhesive DK-2 are described in this per.
本文叙述了DK-2抗磨胶粘剂的配方、物理性能和粘接强度。
Objective To study the effects of colour on diametral tensile strength and bonding strength of resin.
目的：研究颜色的不同对树脂粘结剂径向抗张强度及其与瓷粘结强度的影响。
The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process.
在合适的电刷镀工艺下，镀层表面平整、光滑，具有较高的显微硬度、耐蚀性和结合强度。
A new method for measuring bonding strength between electroplated layer and substrate of diamond tool is proposed.
提出一种新的电镀金刚石工具镀层与基体结合强度测试方法。
In adhesive bonding repair using composite patches, the size of patch has an obvious influence on bonding strength.
在复合材料胶接修补中，补片的尺寸对胶接强度的影响非常关键。
The results prove that the initial bonding strength mostly depends on total reduction and heating temperature of al.
结果表明，轧制变形程度和铝层加热温度都是影响复合板初结合强度的主要因素。
In ultrasonic wire bonding process, the bonding pressure is one of the most important factors to the bonding strength.
在超声引线键合过程中，键合力是影响键合强度的重要因素之一。
The effect of the hot diffusion on the bonding strength and the microstructure of the coating was individual discussed.
并且针对热扩散对涂层的结合强度及组织的影响分别进行了论述。
The bonding strength of the composite interface is reduced when too low or too high extrusion temperatures are employed.
挤压温度过高或过低导致界面结合强度降低。
The melting state of powder and bonding strength of coating did not vary much within spraying distance in the experiment.
在试验的喷距范围内，喷距对粉末的熔化状态和涂层结合强度均无明显影响。
Bonding tests showed that compressing method could improve 5% of panels' bonding strength and percentage of wood failure.
剪切实验表明，胶合板的胶合强度和木破率都由于单板的压缩均提高了5％左右。
Selection of adhesive for bonding strength fi eld pull-out tests of thermal insulation layer and substrate was introduced.
介绍了在保温板材与基层的粘结强度现场拉拔试验中粘结剂的选用。
Experimental results showed that the bonding strength of metal-coated diamonds with alloy or metals was improved markedly.
实验表明，渗覆金属处理可以使粘结合金或金属对金刚石的粘结力大大增强。
Objective:To study the effects of duty cycle and frequency of microarc oxidation(MAO) on the titanium ceramic bonding strength.
目的：观察钛试样在微弧氧化处理过程中，不同的占空比和脉冲频率对钛瓷结合强度的影响。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。
The bonding strength is ensured by the correct choice of substrate material, surface preparation, adhesive and process parameter.
粘合强度可以通过选择正确的基体材料、表面处理、胶粘剂和工艺参数得以保证。
The results indicated that increasing the deformation and a proper rolling temperature may improve obviously the bonding strength.
研究表明，增加变形程度和选择合适的轧制温度能提高复合板的界面初结合强度。
The results show that the joint forms which have less stress, concentration and less peel stress can raise bonding strength greatly.
试验结果表明：降低应力集中及剥离应力小的接头形式可有效地提高胶接强度。
In the present paper, a new model, a layered composite beam, is presented for determining the interface bonding strength of materials.
本文提出了一个确定层状复合材料界面结合强度的新模型，即由两种材料交替完全粘结在一起的复合梁。
The bonding strength of joint zone made by direct and indirect bonding was evaluated and their fracture characteristics were analysed.
对直接连接和间接连接接头的接合强度进行了评估，并对接头断裂特性进行了分析。
The equipment for measuring bonding strength of gunning mix is developed, the structure, measuring method and application are presented.
开发出用于测定喷补料接着强度的试验装置，介绍了装置的组成、 测定方法和应用试验。
After adding can obviously improve the initial bonding strength, peeling strength and cohesive force, and achieves the best balance point.
添加后可明显提高初粘力、剥离强度和持粘力，并使之达到最佳平衡点。
应用推荐