Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
一般来说,气缸和气缸盖用螺栓紧固在一起,气缸与气缸盖之间用一薄垫圈确保密封良好。
ANSI flange sealing principle is very simple: bolt two seal face mutual extruding flange gaskets and formed the seal.
ANSI法兰的密封原理极其简单:螺栓的两个密封面相互挤压法兰垫片并形成密封。
In order to maintain the seal, you must maintain the tremendous force of the bolt.
为了保持密封,就得维持巨大的螺栓作用力。
The design calculation of the large O ring rubber self energized seal (without bolt and nut )used for the vacuum equipment and its application results are introduced.
介绍真空设备法兰采用大直径O形环橡胶自紧式密封(不用螺栓和螺母)的设计计算及其应用效果。
Such as whether the bolt is tightened, the piston ring is installed correctly, damaged oil seal is replaced, etc.
譬如螺栓是否拧紧,活塞环安装是否正确,损坏油封是否更换等。
The fracture causes of joining bolt joined between feeder and quill shaft of ball mill are biggish gap between feeder and quill shaft, defective seal cone washed by ore pulp.
球磨机进料器与中空轴联接螺栓断裂原因是进料器与中空轴之间间隙过大,密封锥面受矿浆冲蚀而被破坏。
The fracture causes of joining bolt joined between feeder and quill shaft of ball mill are biggish gap between feeder and quill shaft, defective seal cone washed by ore pulp. etc.
球磨机进料器与中空轴联接螺栓断裂原因是进料器与中空轴之间间隙过大,密封锥面受矿浆冲蚀而被破坏。
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
本阀可水平安装或垂直安装,安装时两法兰联接中间必须加密封垫片,然后均匀锁紧螺栓。
The application of bolt support in No. 2 seal of Xiyu mine and its spreading is introduced; its benefit and problems are also pointed out.
介绍煤巷锚杆支护在西峪煤矿2号煤层的应用及全面向其它煤层的推广使用,并指出了锚杆支护的效益及尚需解决的问题。
A rubber gasket seal is used between a clamp nut of a barrel screw bolt and the outer wall of the barrel body of the utility model.
筒体螺栓的紧固螺母和筒体外壁之间也采用橡胶垫圈密封。
Pay attention to the direction of medium in valve body. Add seal cushion between two flanges connection and screw down bolt.
安装时请注意阀体上标注介质流向,两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
A valve body is connected with a tower cover through soft seal, and pressed by a bracket through a bolt. The valve rod, the tower cover and a gland are pressed and sealed by filler.
阀杆、塔型盖、格兰通过填料压紧密封,阀杆与执行机构通过固定于支架上的推力螺母实现上下运动。
A valve body is connected with a tower cover through soft seal, and pressed by a bracket through a bolt. The valve rod, the tower cover and a gland are pressed and sealed by filler.
阀杆、塔型盖、格兰通过填料压紧密封,阀杆与执行机构通过固定于支架上的推力螺母实现上下运动。
应用推荐