Post buckling analysis was traditionally conducted by arc length method.
结构后屈曲分析传统上都是采用弧长控制法来处理。
A numerical model based on the finite element method incorporating an arc-length algorithm for nonlinear full-range analysis of UPC beams was developed.
建立了基于有限元方法并结合一种弧长算法的适用于UPC梁非线性全过程分析的数值模型。
In this paper, a numerical method is presented for nearly arc length parameterization of parametric curve.
讨论参数曲线近似弧长参数化的数值方法。
Newton Raphson method is used to solve the non linear equations piloted in displacements or in arc length.
非线性方程采用位移引导或弧长引导的牛顿-拉夫森增量迭代法求解。
Through the calculation of the finite element method(FEM) models for double circular arc profile spiral bevel gear, the stress changing pattern along the length of the tooth is obtained.
用有限元方法，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算。通过应力计算结果的分析，得出了凸、凹两齿侧应力沿齿长的分布规律。
A easy and feasible method to precisely measuring arc length on part's convexity is introduced in this paper.
介绍了一种精确测量零件凸面弧长的较简便易行的方法。
Because arc length of trajectory is regarded as the variant in geodesics based method, it possesses the advantages of non-time based trajectory planning at the same time.
本文的基于测地线的轨迹规划是以轨迹弧长作为参考变量的，因此它还具有非时间参考的机器人轨迹规划的优点。
The geometric progression technique and three dimension arc length technique are combined to form a new method.
利用等比数列网格生成技术，三维弧长生成技术以及拼接技术生成计算网格。
The method of arc-length parameter space provides a good solution for the surface grid of complex geometry contour, and establishes the foundation for the further analysis carried out.
该方法为具有复杂几何外形的物体表面网格的生成提供了一个便利的途径，也为进一步生成三维空间网格奠定了基础。
You should try a Nonlinear analysis, possibly with Arc length control method.
应该试一下非线性分析，可能要用弧长控制法。
An artifice of passing through and evaluating bifurcation points and an improvement for the arc-length method are presented.
一个跨越和求取分支点的技巧和对弧长法的一个改进在文中提出。
Four spectral lines with different wave length of sodium atom were selected in measuring the arc temperature by Boltzmann's Graphical Method.
试验选用了钠原子四条不同波长的谱线，用玻耳兹曼图解法求得电弧的温度。
The method mostly use of two modes that are time Angle and arc-length.
其方法主要采用两种方式：时角法和弧长法。
Double nonlinear factor was considered in the structure analysis. To calculate the ultimate bearing capacity, the equilibrium path of the load and displacement using arc-length method was traced.
结构分析考虑双重非线性情况，采用弧长法跟踪整个荷载—位移全过程的平衡路径，确定极限承载力。
Double nonlinear factor was considered in the structure analysis. To calculate the ultimate bearing capacity, the equilibrium path of the load and displacement using arc-length method was traced.
结构分析考虑双重非线性情况，采用弧长法跟踪整个荷载—位移全过程的平衡路径，确定极限承载力。
应用推荐