Higher the rake Angle, better is the cutting and less are the cutting forces, increasing the rake Angle reduces the metal backup available at the tool rake face.
前角越大，则切削越好且切削力越小，增加前角可以减少刀具前倾面上产生的金属阻塞。
The influencing orderliness of the cutting depth and the rake Angle of the tool on cutting qualities are found and the mathematical models are built.
得出了切削厚度与刀具前角这两个切削参数对切削质量影响的规律，得出二者关系的数学模型。
This method can be used to generate tool paths that have a variable user-controlled lead angle, but maintain cutting with the side of the tool.
此方法可用于生成刀具路径，该刀具路径具有用户控制的可变导引角，但始终使用刀具的侧面进行切削。
The results show that the effects on surface roughness are feed speed, depth of cutting , tool rake angle and parts hardness in turn.
结果表明：工件进给速度对表面粗糙度的影响最大，切削深度和刀具前角次之，工件硬度影响最小。
The effective ways to achieve the wider fiber formation regions can be obtained by increasing the cutting speed and the relief Angle of tool, and decreasing t...
提高切削速度、降低振动杆固有频率、适当增大刀具后角是扩大纤维生成域的有效途径。
The effective ways to achieve the wider fiber formation regions can be obtained by increasing the cutting speed and the relief angle of tool, and decreasing the frequency…
提高切削速度、降低振动杆固有频率、适当增大刀具后角是扩大纤维生成域的有效途径。
The effective ways to achieve the wider fiber formation regions can be obtained by increasing the cutting speed and the relief angle of tool, and decreasing the frequency of vibration staff appr…
提高切削速度、降低振动杆固有频率、适当增大刀具后角是扩大纤维生成域的有效途径。
The effect of tool rake angle on the geometric shapes of the chip, cutting force and cutting temperature is investigated.
分析了刀具前角对切屑几何形状、切削力和切削温度的影响。
The effects of cutting parameters, the tool rake Angle, cutting thickness and speed, for bamboo on cutting forces are studied on this paper.
研究了竹材切削不同刀具前角、切削量与切削速度对切削力的影响。
Five-axis NC machine tool with small pendulum Angle table can not carry out continuous cutting of the part of centrifugal turbine because of the structure of machine tool.
由于工作台摆动角度受机床结构的限制，小摆角五坐标数控机床不能直接进行离心叶轮的连续加工。
On the basis of improving cutting-tool angle and operating method, the machining efficiency is raised, the difficulties in processing inside whorl are also solved.
通过改进刀具角度及操作方法，提高了加工效率，解决了内螺纹加工的难点。
In the simulation, the WC hard-alloy cutting tool was built in according to meet the GB, in which the real shape of cutting tool and the angle parameters in the mounting are also considered.
按照实际加工条件建立了切削模拟模型，按照国家标准建立的硬质合金可转位刀片的三维模型既考虑到真实的刀片几何形状，也考虑了其安装角度参数。
Cutting tool clearance Angle influence plow chip curl situation as well as fin chip superficial situation, but these two conditions are decision flyaway plow chip heat control abilities.
刀具的后角影响犁削片的卷曲情况以及翅状犁削片的表面情况，而这两个条件是决定翅状犁削片的热控制能力。
This paper primary coverage is truncates in the process in the plow the cutting tool best clearance Angle research.
是在犁削过程中刀具的最佳后角的研究。
This paper primary coverage is truncates in the process in the plow the cutting tool best clearance Angle research.
是在犁削过程中刀具的最佳后角的研究。
应用推荐