The solutions of a large deflection problem of thin orthotropic circular plates with variable thickness under uniform pressure and under concentrated load are obtained in this paper.
本文给出了正交各向异性变厚度圆薄板在均布载荷与集中载荷作用下大挠度问题的解。
Based on the piezoresistive effect, large or small deflection theory, thin film's stress theory and other mechanics or electricity knowledge, a piezoresistive micro pressure sensor is designed.
利用压阻效应、大(小)挠度理论、膜的应力形变等力学、电学知识设计了一种压阻式微压力传感器。
A simplified analytical method for the elastoplastic dynamic large deflection response of portal frames under impact loading is reported in this paper.
本文报道一种求解门式刚架在冲击载荷作用下动态弹塑性大变形响应的简便分析方法。
In this paper, a novel system is developed for the measurement of deflection of large structures.
本文介绍了一种用于大型土木工程结构的投影式光学挠度测量系统。
A new approximate formula for the large deflection problem of compression bar with two ends are simply supported is obtained, by the use of Ritz-Galerkin method.
通过非线性振动中常用的里兹-伽辽金法，推出了两端铰支压杆大挠度问题的一个新近似公式，计算结果表明具有较高的精度。
A model for analyzing the large deflection of an elastic cantilever beam with constraint under uniformly distributed load was established.
建立了分析均布载荷作用下受约束悬臂梁的弹性大变形三阶段模型。
The results show that the deflector has the features of a large, bidirectional angular deflection and fast time response.
测量结果表明，这种微偏转器的特点是可双向偏转且偏转角度大且具有快的时间响应。
A new approach to the solution of large deflection bending problem of thin plates is presented by using boundary element method.
本文提出一个用边界元法求解薄板大挠度弯曲问题的新途径。
When the initial deflection of a long pipe subjected to lateral loads is large, the effect of the initial deflection on critical buckling force for the pipe must be considered.
当初弯曲最大挠度比较大时，对于受侧向力作用的较长管柱，初弯曲对管柱轴向临界压力影响很大，必须加以考虑。
So far many approximate methods have been used to solve the large deflection problems except that only a few exact solutions have been investigated but no strict proof on convergence is presented yet.
迄今为止，除了少数未从数学上严格证明其收敛性的精确解外，大多数均采用近似方法求解。
A position detection system is incorporated into a parallel plate interferometer in order to realize large deflection Angle measurement.
为了实现较大的偏转角度测量，该平行平板干涉仪引入了一位置探测系统。
The approach is based on large deflection characterisation of a curved beam, coupled with fracture mechanics concepts.
该方法是基于曲梁大变形理论及断裂力学而提出来的。
A research method of the large deflection of the throttle slice of the hydropneumatic spring was presented.
提出了一种研究油气弹簧环形阀片大挠曲变形的方法。
Finally, the actuation characteristic of large-deflection compliant mechanisms is analyzed as a primary study.
最后对大变形柔顺机构的驱动特性进行了初步分析。
The high-aspect-ratio flying wing eliminates vertical tail and conventional rudder, and uses instead a split drag rudder with large deflection as its directional control surface.
大展弦比飞翼布局飞机取消了垂尾和常规方向舵，通常采用大偏角的开裂式方向舵作为偏航操纵面。
The calculation for the deflection and stability of large scale horizontal cylinder is a problem needed to be solved in the practical projects.
大型卧式液压油缸挠度与稳定性计算是实际工程需要解决的问题。
In this paper, the elastic rod theory is applied to establish a static analytical mechanical model for a small strain, large deflection Marine pipeline during installation in ocean.
本文运用弹性杆理论建立了小应变、大挠度铺设过程中海底管道的静态分析力学模型。
In this thesis a new numerical method - the finite volume method is developed to achieve the static and dynamic large-deflection response analysis for suspension cables.
本文建立了一种新的数值方法——有限体积法进行悬索的大挠度(几何非线性)静力分析和动力响应分析。
In this paper a hybrid perturbation - weighted residual method is proposed for the large deflection of a circular.
本文采用摄动-加权残值联合法求解圆板大挠度问题。
This paper presents a new solution of the large deflection dynamic response of stiffened plates under lateral impact loading.
用半解析的方法分析了横向冲击载荷下加筋板的非线性瞬态响应。
The development of flexure hinges with large deflection, low stress, small parasitic center shift has always been a difficult problem.
大变形、小应力、小中心漂移的柔性铰链的研制一直是柔性铰链研究的难题。
The loading of a tubular busbar is equivalent to that of a large-span beam, and the stress on the cross -section is mainly the tensile stress of the dead weight bending moment with much deflection.
管型母线受力状况相当于大跨度的梁，截面上的应力主要是自重弯矩的拉应力，挠度比较大。
The loading of a tubular busbar is equivalent to that of a large-span beam, and the stress on the cross -section is mainly the tensile stress of the dead weight bending moment with much deflection.
管型母线受力状况相当于大跨度的梁，截面上的应力主要是自重弯矩的拉应力，挠度比较大。
应用推荐