动态激励装置由驱动电机进行驱动。
变频器驱动电机，实现调速运转稳定。
Frequency converter drives motor to realize stable velocity change operating.
于是人们期待着一种新的驱动电机的出现。
So people are looking forward to a new drive motor to appear.
假如是电驱动设备，要切断驱动电机的电源。
For electric driven equipment, disconnect power to the motors connected to the equipment.
步进状态转动的直流马达是很理想的驱动电机。
Direct current motor rotating in step mode is the ideal drive motor.
采用VMOS管驱动电机，使得驱动电源稳定可靠。
The driver was stable and reliable by using VMOS transistors to drive stepping motor.
研究了电动汽车驱动力和相应驱动电机功率的计算。
The thesis also introduces calculation of drive and power of induction motor.
经过风轮叶片的空气迫使风轮旋转，风轮驱动电机。
重点介绍了送风机和其驱动电机的典型故障及其特征。
The typical troubles of forced draught fan and its driving motor are mainly introduced.
直接驱动电机的手段是重视碗和控制电子-有没有变速箱。
Direct drive means the motor is attached to the bowl and controlled electronically - there's no gearbox.
实现了对机器人驱动电机、超声传感等任务模块的系统控制。
The control of driving motor module and ultrasonic sensor module are realized in the system.
驱动电机采用国内知名品牌，采用电子变频调速技术使其加速平稳。
The electronic converter speed adjustment technology is adopted by driving motor of famous logo of domestic to feature more stable in accelerating state.
部分转子泵采用的是简单的直齿轮驱动电机，电机采用地脚螺钉固定。
Used part of the rotor pump is a simple spur gear drive motor, electric screw fixation using pin.
根据电传动履带车辆使用要求，选择表贴式永磁同步电机作为驱动电机。
According to the requirements of an electric armored vehicle, a surface-mounted permanent magnet (SPM) motor is selected as the driving motor.
为了满足螺杆空压机运行中的节能，必须有一种高效率变转速的驱动电机。
In order to meet the screw air compressor operation of the energy saving, there must be an efficient change speed motor drive.
将驱动电机置入灵巧手指内部，使得灵巧手指自重对操作性能的影响增大。
Placing driving motors in the dexterous robotic fingers will enable the fingers self weight to have a greater influence on its operation capability.
PWM逆变器驱动电机时，对电源端产生谐波电流，给电力电网造成污染。
PWM inverter AC motor bring the harmonic current, It pollute electric power systems.
如果汽车需要更多的里程，燃气发动机就投入使用，产生额外的电能来驱动电机。
If the car needs more range, a gas engine kicks in to power a generator that creates additional electricity for the electric motor.
提出了一种用无位置传感器的无刷直流电动机来作为电作动器的驱动电机的思想。
An idea is developed in the paper that position-sensorless BLDC motor is used as driver of EMA, with the advantages of maintenance and reliability besides small size and light weight.
根据对受力零部件的动力学分析结果，可以合理选择驱动电机、轴承等关键零部件。
According to the dynamics analysis result of forced parts, choose reasonably the key parts of motors, bearings etc.
反应式步进驱动电机的转子无绕组，由被励磁的定子绕组产生反应力矩实现步进运行。
Reactive stepping motor rotor windings without, the excitation of stator winding respond to realize stepping operation torque.
结果表明，将驱动电机和机构作为一个完整的系统进行综合优化研究更符合实际情况。
The result shows that let the driving motor and mechanism be acted as a complete system to carrying out the synthetic optimization study could be further accord with the practical situation.
反应式步进驱动电机的转子无绕组，由被励磁的定子绕组产生反应力矩实现步进运行。
Reactive stepping motor rotor windings without, the excitation of the stator winding reacts to achieve step operating torque.
使用时务必查清，如有疑问可找专业人员帮助解决，否则会损坏自动充气机的驱动电机。
It is necessary to make it clear when in use, ask special persons for help if any inquiry, otherwise, drive motor of auto inflator may be damaged.
这些精度放大器可以用于驱动电机、压电设备、可编程电源以及其他需要高功率和精确控制的设备。
These precision amplifiers are used for driving motors, piezo electrics, programmable power supplies, and other devices requiring high power and precision control.
双坐标联动丝架是在丝架上增加了U、V两个驱动电机，通过程序控制来实现锥度切割。
Double coordinate gang wire has added U. V. two drive motors to carry out taper cutting by program control.
本文论述了一种新型轨道移动式清篦破碎机其传动系统的驱动电机功率的理论计算方法。
This paper discussed the method of the theoretical calculation of power for driving motors in the breaking and drive system of a new track-sliding and grid-cleaning crusher.
根据系统的控制要求，选用TMS320 LF 2407 A作为驱动电机的控制芯片。
According to the demand of the system control, the DSP - TMS320LF2407A is chosen as the control chip of the drive motor.
利用两足步行椅机器人动力学模型，分析了各关节的驱动力矩，以此确定了驱动电机的功率。
A dynamics model of the robot is used to analyse the driving torque of each joint, and the driving power of motors are decided based on the analysis results.
讨论了精密气浮轴系、驱动电机、装夹调心装置等关键部件的设计问题及测量系统的工作原理。
The measuring principle and some design problems of key techniques, including precision air - bearing, driven motor, fixture and aligning devices were discussed.
应用推荐