阶跃信号在地震仪的脉冲标定和检查中获得了广泛应用。
The step calibration signal has been widely used in seismograph calibration and check.
阶跃信号作用于耦合谐振电路的分析是电路分析中的难点。
The analysis of step signal action on coupled resonant circuit is a difficult part in circuit analysis.
本文对采用阶跃信号动态校准系统的误差分析具有重要的意义。
The results of the paper is significant in error analyzing of dynamic calibration of systems using step-function signals as the input.
介绍的斜度探测器，能够检测信号变化后的斜率大小，有效地识别出阶跃信号的变化。
A slope detector is proposed, which is capable of detecting the slope of varied signals and recognizing the variation of the step signals, although these signals do not have a large slope.
通过频域和时域分析，指出阶跃信号和伪随机信号是一类既有差别又有内在联系的测试信号。
By analyzing time and frequency domain response we found out that they have some internal connections with each other, although the test signals are different.
提出了一种基于时域加权的新的非叠代优化算法，用于重构经过采样示波器测量的阶跃信号、脉冲信号等。
A new non-iterative algorithm with time-domain weighting is described for reconstructing fast, step-like, or impulsive signals that have been measured with a sampling oscilloscope.
因此，设立一个喷雾冷却系统模拟实验室测试的阶跃信号的传统，积分分离模糊自适应PID控制器和模拟铸造。
A spray cooling system is thus set up for simulation in lab to test the step signal from the conventional, integral separated and fuzzy self-adaptive PID controllers and the simulated casting.
当系统存在不定性时，作者分别采用阶跃信号和正弦信号作为参照信号，将滑模变结构控制和PID控制进行仿真比较。
When the system exists uncertainties, the author compares sliding mode control with PID control adopting step signal and sine signal as a reference.
提出一种带修正因子规则的模糊pid控制，分别用这种控制器和常规pid控制器对阶跃信号和车辆的15工况进行仿真分析。
An adaptive fuzzy PID controller with modifying rules is introduced and is compared with ordinary PID controller by simulation on step response and response of 15 operating modes.
在十三陵抽水蓄能电站辨识试验中，使用给定功率阶跃扰动信号进行辨识，取得了满意的辨识结果。
In identification experiment of ShiSanling pumped storage power station, reliable results has been achieved by using step disturbance of given power signal.
针对每一种控制算法分别采用阶跃风速和紊流风速信号进行了仿真，仿真结果验证了控制算法的可靠性和有效性。
The simulation is conducted for each control strategy in different wind situations. The results show the reliability and affectivity of the proposed control strategy.
简述了采用伪随机及阶跃激励信号进行系统辨识的原理。
This paper briefly gives principles of using PRBS and step signal to identify system and describes methods of constructing IBM-PC/XT-computers identification system.
发现对待测自由面速度阶跃，磁探针有两种类型稳定的输出信号，分别对应于不同的速度范围。
It was found that there were two types of signal profiles carres ponding to different velocity ranges.
在仿真试验中，比较了给定功率阶跃扰动信号、白噪声信号及伪随机信号分别作为输入信号进行辨识的结果。
In simulation experiment, results of identifying models using step disturbance of given power signal, white noise signal, and pseudorandom signal as input signals have been compared.
仿真结果表明，系统稳定性高，能够较好地跟踪阶跃、正弦和斜坡等典型力信号，对常规气压伺服技术应用领域的拓宽具有重要的理论和实际意义。
Simulation results show that the servo system has high stability and can trace step, sine and ramp force signal with high precision. It is significant to developing the pneumatic servo system.
在目前这个设计中，阶跃输入信号限制在零点几毫伏以下。
In the present design, step inputs are restricted to a few tenths of millivolt.
该方法利用阶跃输入信号获取非线性增益的强一致性估计；利用不同幅值的周期脉冲输入信号获取线性子系统脉冲响应函数的强一致性估计。
The nonlinear gain and the impulse response functions of linear subsystem be obtained by using the step-changeds and cyclic impulse with different amplitudes as input signals.
实验还测定了间距大小对磁探针输出信号的影响，给出了磁探针对阶跃实验的响应波形。
The influence of the crevice width to the gauge output was also tested, the response of jump test was obtained.
计算机模拟结果证实了这种算法不仅可以有效地抑制信号中的噪声，而且较好地保持了信号的陡峭阶跃变化。
The result of computer simulation shows that the filtering algorithm can not only efficiently suppress various noises in signals but also preserve the sharp step changes of the signals.
阶跃呼应信号添加20%额外电压为40ms。
阶跃呼应信号添加20%额外电压为40ms。
应用推荐