通过动力学分析与计算，找出了原因，提出了解决措施。
The reason and solving measurements are discussed by means of dynamics analysis and calculation. And these measurements are feasible.
通过动力学分析和有限元模拟，设计出了具有高过载保护功能的加速度传感器结构。
Utilizing the dynamics analysis and finite element simulation, the acceleration sensor's mechanical structure with high overload protection capability was designed.
通过动力学分析、热分析和静力分析的有机结合，对该类型结构计算进行了有益补充。
The analytical skill of structural analysis can be enhanced by this method which combines dynamic simulation analysis, thermal analysis and static analysis.
通过动力学分析，建立了车型弹性倒立摆系统的动力学控制模型，并对系统进行了线性化和可控、可观性分析。
Its dynamic control mode of vehicle tyre is derived by dynamics analysis, and the linearization, controllability and observability of the system are analyzed.
通过动力学分析，得到了对于单叶双曲面平板直刃滚筒式切碎器切割秸秆层切割阻力矩的数学模型，经过试验验证验证了其有效性。
Based on the mechanics analysis, the mathematical model of the cutting torque was established, and the validity of the model was demonstrated by the experiments.
本文通过实验对曲棍球击球技术进行了动力学分析。
A dynamic analysis on the batting skill of hockey is presented by experiments.
通过金刚石动力学分析说明石墨重结晶是金刚石合成过程中的一个重要问题。
From the diamond's dynamic analysis, it is shown that recrystallization of graphite is a key problem of diamond synthesis.
利用SIMPACK车辆动力学分析软件分析了12轴大型货车的曲线通过性能，得出了车辆曲线通过速度和曲线外轨超高的较佳匹配结果。
The curve negotiation performance of the 12-axle large wagons is analyzed with the SIMPACK vehicle dynamics analysis software.
通过力学分析，建立了离心调速器系统的动力学方程，应用李雅普·诺夫直接方法得到该系统稳定平衡点的条件。
By using mechanical analysis, the dynamic equation of the system was established, the Lyapunov direct method was applied to obtain stability conditions of system equilibrium points.
通过瞬态动力学分析得到钻柱在瞬态冲击下的应力、位移变化规律，为故障的发生点提供理论仿真依据。
Obtained Stress, displacement variation of oil drill through the analysis of transient dynamics, Point to the occurrence of failure to provide the theoretical basis for simulation.
通过对关节式移动机器人越障过程运动学和动力学分析，得出控制移动机器人越障时保证动态稳定性的约束条件。
Analyzed kinematics and dynamics of the obstacle negotiations for an articulated mobile robot a restriction condition to guarantee dynamic stability when it gets over the obstacles.
通过对离合器传动系动力学分析，建立了车辆起步时变速器输入轴速度与离合器接合位移之间的传递函数模型。
Transfer function model between the input speed of transmission and the engagement displacement of the clutch is built up through an analysis on the system of drive of the vehicle.
瞬态动力学分析通过考察联轴器传递转矩过程中的最大应力、最大位移及其发生部位来分析联轴器的动态刚度和强度状况。
The transient dynamic analysis researched the dynamic stiffness and strength of the joint by investigating the maximum stress and strain when it transmits torque.
通过刚柔耦合仿真和刚体模型仿真的比较，得出柔性体对摇摆台性能的影响因素，同时为十字轴的动力学分析和优化提供必要的动态载荷。
Based on this simulation, it conclude the difference between rigid body and flexible body, and also supplied necessary dynamic load for spider's dynamic analysis and optimization.
本研究将通过步态相关的动力学分析对传统标准手术入路与微创入路作一比较。
In the present study, a minimally invasive approach was compared with a traditional standard approach in terms of the effect on gait kinematics as demonstrated with gait analysis and electromyography.
通过实例分析表明，非线性动力学分析方法是行之有效的。
The effectiveness of the nonlinear dynamic method is confirmed by the practical analysis.
该文通过对车辆的动力学分析，建立了事故再现中的汽车轨迹模型，并实现了计算机软件，最后对模型进行了验证。
Through the dynamic analysis of vehicle, the Vehicle Trajectory Model is built, and the programming of the model is established and validated in the paper.
并在此基础上通过建立力学数学模型完成旋转控制头在安装偏斜的情况下的动力学分析。
And then, the mathematics model was firstly set up to analyze the force that the rotary control head endured when the preventer installed aslant.
本文通过水动力学分析及实际资料分析，认为现存的水流挟沙力多值关系的说法是存在问题的。
Through the analyses of hydrodynamics and natural data, it can be considered that the concept that the sediment carrying capacity of flow has many values is questionable.
并通过对组织学习过程的系统动力学分析，建立组织学习过程的系统动力学模型，重点描述认知过程中主体之间的相互关系和各因素的作用。
It also builds systematic dynamics model to illustrate the relationship and function of key factors in recognitive process by analysis on the organization learning process.
通过运动分析给出了实现径向直线伸缩运动的必要条件，进行了净化机器人的运动学与动力学分析。
According to motion analysis, the necessary conditions for realizing the radial rectilinear motion were given and the kinematics and dynamic analysis of the cleaning robot were discussed.
通过模态实验校验的手段证明用这种方法进行榫接装配系统动力学分析是可行的。
Through modeling experiment , this method is proved to be feasible for analyzing the rabbet assembly structure.
通过风力机空气动力学分析和模型研究，为变桨距控制提供了理论基础。
Based on the research of wind turbine aerodynamics characteristics, a model was established and the theoretical foundation of pitch control was built.
通过对光电桅杆在复杂海洋工况下的水动力学分析，得到了光电桅杆的相关力学参数。
This article demonstrates the hydrodynamics analysis for the optronic mast in a complex marine application environment, and then derives the dynamics parameters of optronic mast.
本文主要通过对动平衡测试系统的动力学分析，推导车轮综合不平衡与平衡校正质量的大小和位置。
From which the correcting mass quantity and location related to the adjustment of the synthetic unbalance of motorcar wheels were derived.
通过动力学和热力学分析，建立了以果胶为稳定剂的酸乳饮料的动力学和热力学稳定性预测模型。
The stability prediction model of acidified milk drinks with pectin as stabilizer was built through the analyses of kinetics and thermodynamics.
通过进行模态分析，为塔架设计、安全运行和结构动力学分析提供更可靠的理论依据。
It provides theoretic basis for the design and safe operation of the tower and the further dynamic analysis of wind turbine tower through the modal analysis.
本文建立了基于ANSYS有限元分析软件的光学振动失调物理模型，通过瞬态动力学分析得到了反射镜在振动激励下的位移响应。
Physical model of misaligned optical system under interference vibration was developed based on ANSYS and the dynamic response of the reflector was obtained by transient dynamic analysis.
通过ANSYS的APDL流程化分析功能的开发，实现了血流动力学分析的流程化、自动化。
By the APDL function of ANSYS, VRCF can analyze hemodynamics conveniently and automatically.
通过ANSYS的APDL流程化分析功能的开发，实现了血流动力学分析的流程化、自动化。
By the APDL function of ANSYS, VRCF can analyze hemodynamics conveniently and automatically.
应用推荐