介绍了基于CAN总线的通信节点设计方法。
This paper introduces the way of designing communication node based on CAN bus.
本文通过无线通信节点间的合作，提高网络的性能。
In this paper, we improve network performance through the cooperation between wireless nodes.
中间有封装的通信节点的包(排队等)和节点之间的通信是通过使用。
There is a node package in the middle which encapsulate the communication (queueing etc) and the only communication between nodes is through Redis.
最后通过实例计算分析了三种结构系统平均可靠度受通信节点数影响的情况。
Lastly, the circumstance which the system average reliability of three topologies is affected by the node number is analyzed by an illustration.
这种免费赠送的功能发生于网络中通信节点之间与atm结构模型相同的层上。
These complimentary functions occur between communicating peers in the network at the same level of the ATM architectural model.
开发工作主要包括了：通信节点设计、硬件接口设计以及软件程序的编写三个方面。
The main work includes the design of the node, the design of the hardware interface and software programming.
集中器和通信器是本系统的通信节点，它们使控制网络的信息和命令可以通过电力线传输。
The collector and the communicator are communication nodes of the system. They enable the control network to pass the information and commands through power line.
它们对于计算机网络中网络服务器、主机和通信节点机的容错设计都具有良好的参考价值。
These typical computer systems are valuable for the fault tolerant design of network servers, host computers, and communication node computers for computer networks.
软件设计主要是对通信协议的实现，文中给出通信节点的主程序和几个重要子程序的流程。
The main task of the software design is to realize the communication protocol and the flows of several important subprograms and the main program of the communication nodes are given in the paper.
这个量子密钥传输协议在通信节点和控制中心之间通过多个GHZ对构建安全的密码分配系统。
The quantum communication network marries a variety of GHZ states to well establish the secure key distribution system employed in conjunction with the nodes and control centers.
本文就通信节点的电力线通信性能做了测试和分析，实验结果表明该智能建筑控制网络通信系统是可行的。
The PLC performance of the communication nodes is tested and analyzed. The results show the communication system of the control network of intelligent building is feasible.
最后基于LPC 2194微控制器和TJA1050高速CAN总线驱动器开发了各通信节点。实际应用表明，该系统稳定可靠。
Communication nodes are developed based on microcontroller LPC2194 and high speed CAN bus driver TJA1050. The application shows that the network is reliable and stable.
联合紧急业务需求订单包括在两架庞巴迪BD-700全球快车飞机和两架20座全球鹰无人机上安装战场机载通信节点（BACN）。
Tasking under the joint urgent operational need includes installing BACN on two Bombardier BD-700 Global Express aircraft and two Global Hawk Block 20 unmanned aerial vehicles.
要使一个IP网络中的两个节点能够通信，那些IP地址必须在整个网络中是唯一的。
To enable communication between two nodes in an IP network, those IP addresses have to be unique among the whole network.
此模型依赖部署管理器与其托管节点之间的紧密耦合的可靠通信链路。
This model relies on tightly coupled reliable communication links between the deployment manager and its managed nodes.
每个逻辑节点都分配了一个通信端口。
Each of the logical nodes is allocated a communication port.
您指定的主机名称或IP地址就是其他节点将用于与正在创建的节点通信的主机名称或 IP地址。
The host name or IP address that you specify is what other nodes will use to communicate with the node being created.
每个节点都通过代理与部署管理器通信。
Each node USES an agent to communicate with the deployment manager.
在这个错误场景中，节点之间的通信链发生故障，每个节点都认为自己是主节点。
In this error scenario, the communication link fails between the nodes, and both nodes believe that they are the primary node.
节点之间的通信也要通过网络。
接下来，让两个节点相互通信。
Next, we will make the two nodes communicate with each other.
与以太网和传真机不同的是，XForms并非网络上任何两个节点间的正式通信协议。
Unlike Ethernet or a fax machine, XForms is not a formal communication protocol between any two nodes on a network.
计算节点间的通信在“计算”网络上进行，它是一个运行于eth0上的私有网络，如图1所示。
Communication between the compute nodes occurs on the "compute" network, which is a private network running on eth0, as shown in Figure 1.
作为根用户发出以下的preprpnode命令，让现有节点和新节点能够相互通信。
Issue the following preprpnode commands as a root user to allow communication between the existing nodes and the new node.
Kerberos协议允许在不安全的计算机网络上通信的计算机节点以一种安全的方式互相验证。
Kerberos protocol allows computer nodes communicating on a non-secure computer network to authenticate each other in a secure manner.
一旦安装了openMosix，集群中的节点就会开始通信，并且，集群通过优化资源分配，不断地根据工作负载 对自己进行调整。
Once openMosix is installed, the nodes in the cluster start communicating and the cluster continuously adapts itself to the workload by optimizing resource allocation.
您将再次使用集群管理器Web服务，确保管理器与节点之间的通信，并测试节点之间的通信。
You'll revisit the cluster manager Web service, ensuring communication between the manager and the nodes and testing communication among the nodes.
在所有节点上发出preprpnode命令，从而使集群节点能够相互通信。
Issue the preprpnode command on all nodes to allow communication between the cluster nodes.
bcast指令表示节点将通过此接口彼此通信并执行ping操作。
Bcast is a directive that means the nodes will communicate and ping each other on this interface.
SV - 2系统通信描述为物理节点及其相关的通信基础构架建模。
SV-2 Systems communications Description Models physical nodes and their related communications infrastructure. Composite structure Diagram Deployment Diagram 6.
应用推荐