海亿达混凝土泵性能稳定，工作可靠，实现了更强的泵送能力、更快的泵送速度、更少的堵管，更优的机器性能。
HYD Concrete pump offers stronger pumping ability, quicker pumping rate, little pumping jam, and better ma-chine performances.
分析了主要工艺参数如：激光功率、扫描速度、送粉量以及Z轴增量对成型质量和形貌的影响。
The technics parameters, such as the laser power, scan velocity, powder feed rate and the Z axis increment, which influence quality and shape were analyzed in this article.
通过改变送粉激光熔覆过程中的扫描速度、送粉速率、基体预热温度等工艺参数，获得了单道激光熔覆层。
Single pass laser surface of the specimens using powder feeding method were obtained by varying the powder feeding rate and the preheating temperature of the substrate.
在单道熔覆中通过跟踪测量研究了激光功率、扫描速度、送粉速率、光斑直径和基体预热温度对熔池温度的影响规律。
The influence of laser power, scanning speed, powder feed rate, spot diameter and preheating on the temperature of molten pool were revealed in the process of single-pass cladding.
采用波形控制方法对熔滴过渡周期进行控制，同时软件还对时序系统和送丝速度进行精密渐变控制。
The droplet transfer cycles were controlled by wave control method. Also gradual adjustment of the sequential and wire feed rate was controlled by software.
提出了一种实用的带送物料流位移和速度检测方法。
A practical measuring method of the displacement and velocity of the material flow is proposed.
个性化的手动模式：可输入适合的3段手动速度，让使用者更容易操作，精确地使材料送近模具而定位。
Manual model : it can input 3 phases manual speed, which can let used operate more easily and feed materials more accuracy.
结果表明，预处理、送粉量、激光的扫描速度是决定模具修复质量的关键。
The results show that repairing quality of the dies is affected by pretreatment, laser power scanning rates and powder feed rates.
新研制的、适用在MIG、MAG焊接中，作测定送丝速度和在焊接生产中作质量检测的CSY一1型测量仪。
A new developed instrument Model CSY-1 for measuring wire feed rate in MIG and MAG welding and for detecting quality in welding process is given.
改变能量输入的层厚控制：送粉条件不变时，熔覆层厚度随熔池温度的增加而增加，通过控制激光功率或扫描速度可以实现熔覆层厚度的反馈控制。
The control of layer thickness by changing energy input. When the powder feed conditions were constant, the layer thickness was increasing with the increase oftemperature of melt pool.
用FIDAP软件模拟了一典型大空间建筑空调采用置换通风送、回风口同侧布置、异侧布置的室内空气流动的速度场和温度场。
Velocity field and temperature field of replacement ventilation of air-conditioning in a typical large space building are studied using FIDAP software.
注：送丝速度及焊接电压设置范围与配套焊接电源相关。
Note: the wire feeding speed and the welding voltage are dependent on the selected welding power.
由控制电路实现焊接程序的控制，带电枢电压负反馈的调速电路控制和调节送丝速度。
The control to welding procedure is realized by a control circuit, and wire feed rate is regulated and controlled by speed governing circuit with the armature voltage negative feedback.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjusters were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
送丝速度通过两个PI调节器进行双闭环控制，分别进行电枢电压反馈和电弧电压反馈。
Two PI adjustors were applied for wire feeding velocity control, one performed motor armature voltage feedback, the other one executed arc voltage feedback to determine the given velocity.
风扇冷却，过热保护，送丝速度可调节。
Fan cooled, with thermal protection, equip with speed control regulator.
随着送丝速度的变化，熔滴过渡各阶段时间影响液桥分断时的表面张力过渡。
With the variety of wire feed speed, the interval of each phase of droplet transformation has a great influence on the breaking state of liquid Bridges.
而送丝速度的调节快慢除了受控于实际的控制系统外，还受电机惯性的影响。
But the adjustment speed of wire feeding is subjected to the actual control system and the motor inertia.
隔张送纸功能，计数器显示生产数量，计速器显示生产速度。
Skip feed for large sheet. Electric counter to indicate production volume, speeder to display the machine working speed.
当需要时帮助接听电话，接受点单。必要时参予送餐工作，以保证服务速度的要求，实现。
Answer the telephone and take orders if needed. Run any order as needed to improve the speed of service and meet an objectiveof 45-minute orders.
在埋弧焊接的变速送丝系统中，其电弧电压的稳定是依靠调节送丝速度实现的。
The stability of arc voltage is realized by adjustment of wire feeding speed in constant wire feeding system of SAW.
采用变速器和磁性离合器调整送纸皮带速度，确保送纸及输纸步距的稳定。
Magnetic Clutch to adjust the belt speed for stable feeding and spacing between blanks.
特别设计的机械式放松装置，在送料速度与冲床配合上达到理想的效果。
Special design mechanical relaxation installment, Achieves the ideal effect in the feeding speed and the punch press coordination.
特别设计的机械式放松装置，在送料速度与冲床配合上达到理想的效果。
Special design mechanical relaxation installment, Achieves the ideal effect in the feeding speed the punch press coordination.
送料、压片，制粒速度均可调节，压力可调，成品细度可调，改进制粒转笼，增加颗粒的成品率。
Feeding, tabletting, granulating speed, the pressure, and particle fineness are all adjustable. Granulation cage is improved to increase the yield of particles.
前者试验获得了一定激光功率和离焦量条件下两组焊接速度和送丝速度的匹配关系，并发现填充焊丝的加入对焊缝咬边现象确有改善；
Two groups of matching relation of the weld speed and the wire feed rate were found in a condition of invariable laser power and focus position.
注：送丝速度及焊接电压设置范围与配套焊接电源相关。
Note: the wire feeding speed and welding voltage set range are dependent on the selected welding power.
标准的双程序转换开关允许操作者设置不同的电压和送丝速度，并在两种程序间相互转换。
Standard dual procedure allows operator to set different voltage and wire feed speeds and switch between the two.
分析了PI控制算法、电源外特性控制算法、送丝速度控制算法，以及控制程序的优化设计。
The paper analyzes the control algorithm of PI, external characteristic of power source and the feeding speed.
分析了PI控制算法、电源外特性控制算法、送丝速度控制算法，以及控制程序的优化设计。
The paper analyzes the control algorithm of PI, external characteristic of power source and the feeding speed.
应用推荐