针对医学器械的特殊要求和实际应用场合，进行仿真分析，为医生制订手术方案提供支持。
For the special requirement and actual application status of medical instrument, the simulation analysis was taken, giving chirurgeon a support to make operating plan.
排气系统具有控制发动机排气噪声的重要作用，所以对发动机排气系统进行仿真分析很有必要。
The exhaust systems play the important role of controlling the engine exhaust noise, so it is necessary to simulate and analyse the characteristics of the exhaust system.
运用键合图理论建立了系统的数学模型，并利用计算机仿真技术对系统的动特性进行仿真分析。
Mathematic model of the system was established by bond graph theory, and then the simulation analysis on dynamic characteristics for it was worked out by computer.
根据力学原理，建立了柔性梁的刚度模型，结合有限元法进行仿真分析，确定出梁的结构参数尺寸。
According to mechanics, a stiffness model of the flexible beam was established. Then the parameters of the beams were determined by a simulation in finite element method.
在此基础上对计算进行简化，减少计算量，并利用机械系统仿真分析软件ADAMS进行仿真分析。
The method not only simplifies the solving process, but also reduces the computations, and using the mechanical system simulation program - ADAMS to simulate it.
通过综合考虑运用计算机进行仿真分析的整个过程，详细介绍了基于分析过程的联合建模的研究思路。
Through considering synthetically with the whole process of the computer simulation analysis, a co-modeling method based analysis process was described in detail.
最后进行了微移动条件下切换机制改进的仿真验证，借助各种成熟的仿真工具对改进方案进行仿真分析。
Finally it carried on the cut mechanism improvement simulation confirmation under the micro motion condition, with the aid of each kind of mature simulation tool to the improvement program.
对磁悬浮隔振器与常规型隔振器并联后在不同电流下的支承刚度特性进行仿真分析，确定磁悬浮隔振器电流上限。
The current upper limit of magnetic suspention isolator can be determined after analysing the supporting stiffness characteristic of multipled magnetic suspention isolator and conventional isolator.
对某轿车整车动力学模型进行仿真分析的结果表明：该模糊PID控制能有效提高车辆的乘坐舒适性和操纵稳定性。
The results of simulation on a car dynamic model demonstrate that the fuzzy PID control can effectively improve the ride comfort and handling stability of vehicle.
应用实测数据对算法进行仿真分析，结果表明：该方法可精确地提供船舶的导航信息，验证了该方法的可行性和有效性。
The measured data and algorithm simulation analysis shows that this method can not only provide precise navigation information for ships but also ensures the feasibility and effectiveness.
不同荷载作用对孔边应力集中系数的影响进行探讨，并就两个主方向的杨氏模量的变化对孔边应力的影响进行仿真分析。
The influence on hole-edge stress concentration factors of different loads is explored. And simulation analysis is made on the influence of Young's modules in the two...
借助于计算机对摆振现象进行仿真分析，研究系统参数对摆振的影响，可以为探索有效的汽车防摆措施提供理论上的指导。
So we have a simulation research on shimmy by computer software and have a study on the effect of system parameters on shimmy, which may offer theory guidance for suppressing shimmy.
与实验相比，进行仿真分析不但能节约人力、物力，而且能方便地分析各种参数对滚动噪声的影响，对降噪具有重要意义。
Simulation need less manpower and material resources than experiment, and it is more convenient to analysing the effect of each parameter to rolling noise.
最后以超宽带认知无线电组成的室内无线个域网为例，给出了平面和空间两种认知场景，并对这两种认知场景进行仿真分析。
Finally, based on an indoor wireless personal area network composed by UWB-CR, the two-dimensional and three-dimensional working scenarios are given respectively, and are simulated and analyzed.
提出一种带修正因子规则的模糊pid控制，分别用这种控制器和常规pid控制器对阶跃信号和车辆的15工况进行仿真分析。
An adaptive fuzzy PID controller with modifying rules is introduced and is compared with ordinary PID controller by simulation on step response and response of 15 operating modes.
对已有的多径时间延迟模型进行仿真分析，重新推导、反复计算、多个公式对比，得到了两个跟实验结果更加接近的修正数学模型。
Reasoning more than one multipath delay formulas simulate them repeated calculation contrast the numerical value, gained two modified mathematic models which are more approach the experiment result.
本文将对其中比较典型的几种方法进行仿真分析，对比各种方法的优缺点，从而为提出更有效的拖船噪声抵消方法提供有力的参考。
This paper analyzed and contrasted several typical algorithms, and the results would provide some helpful references for the research of tow ship noise canceling.
通过应用Matlab中Simulink工具箱对lu混沌系统进行仿真分析，说明脉冲控制是有效的镇定受扰动混沌系统的方法。
Through the application of Matlab in Simulink toolbox of chaotic lu system simulation analysis shows that impulse control is an effective stabilization of chaotic systems by perturbation method.
本文制定了开关投切的工作流程，通过电气参数计算并对开关投切过程进行仿真分析，本文所设计的开关能够实现特大电流的电流转移。
The switching on-off flows are introduced in this paper. By calculating electrical parameters and simulating the switching motion process, the switch can achieve the current transfer of huge current.
最后，采用所提出的方法对两种类型的电源系统进行仿真分析，并与单纯蒙特卡罗方法仿真分析结果进行比较，验证了该方法的可行性和有效性。
The reliability results of two aircraft electrical power systems with the proposed method and the Monte Carlo method are compared, and the result shows the method is feasible and effective.
通过以MATLAB为平台的Advisor分析软件，对所开发的并联式混合动力电动汽车(PHEV)动力总成及传动系参数配置的效果进行仿真分析。
The simulation analysis results of the powertrain of a parallel hybrid electric vehicle (PHEV) are presented based on the given parameter configuration of the transmission system of the whole vehicle.
在研究中，他们开始了全面应用故障仿真系统进行试验，并自编软件对大量仿真数据进行统计分析。
In their research they started to apply the fault simulation system for test in an all-round way and created their own software to analyze the enormous simulation data.
最后，利用Matlab软件的作图功能，从自相关函数、频谱函数和模糊函数三个方面对M波形的性能进行了仿真分析。
At last, making use of the plotting function of MATLAB, the paper carries out simulation analysis from three aspects: auto-correlation function, spectrum and fuzzy function.
另外，还对滤波器的结构和参数对输出直流电压脉动和发电机相电流波形的影响及相电流谐波进行了仿真分析。
In addition, the thesis analyzes the influence of the filter structure and parameters on the output DC voltage ripple and the shape of phase currents, as well as harmonics of phase currents.
在此基础上采用有限元分析软件对永磁材料的磁导率为非线性时的一对永磁齿轮传动磁场进行了仿真分析，并对结果进行了分析总结。
On this basis, as the permeability of permanent magnetism material is non-linear, two gear wheel's magnetic field is simulated with finite element software, and analysis of the result is carried on.
本系统使用内存拷贝技术对显示信号进行动态刷新，使仿真过程更接近侦察系统的信号实时分析。
The simulation process is similar to real time signal analysis of practical reconnaissance system by means of memory copy technique which refreshes display signals.
最后，我们按照IBRAC技术的方法对虚拟门式起重机司机培训系统进行了分析与设计，并分析了门吊仿真系统的性能。
Finally, according to IBRAC technology, this virtual training system for portal crane drivers is analyzed and designed. The performance of this system is represented as well.
最后，我们按照IBRAC技术的方法对虚拟门式起重机司机培训系统进行了分析与设计，并分析了门吊仿真系统的性能。
Finally, according to IBRAC technology, this virtual training system for portal crane drivers is analyzed and designed. The performance of this system is represented as well.
应用推荐