对不同轧辊交叉方式的辊缝特性进行了研究。
The features of roll gap in different cross schemes of roller arrangement were studied.
叙述了型钢轧机采用大辊缝孔型设计的优点和设计特点。
The superlority and feature of using big bite in pass design of section rolling were briefed.
这对矫直机的设计和实际矫直中的辊缝设定有借鉴意义。
These are significantly used for reference for the design of leveler and gap setting during the actual process of leveling.
在板带递送机辊缝变形区中，板带表面容易发生塑性变形。
Plastic deformation is easy to occur on the surfaces of plate and strip in the roll gap of pinch mill.
为内辊缝控制的HCW轧机厚控系统建模提供了理论依据。
These provide theory basis for inner roll-gap gauge-control system of HCW strip mill.
针对某冷轧薄板厂轧机液压辊缝控制系统HGC进行了研究。
Took a research on hydraulic gap control (HGC) system of a cold rolled strip factory.
利用动态连轧理论分析了辊速和辊缝对出口厚度和张力的影响。
The inter-stand tension can be changed by adjusting the roll gap or the roll speed.
利用该结果进行辊缝预设得到的轧件厚度与实测板厚十分接近。
The predicted height of work piece is also accorded with the measured values using the result.
并将修正后的钢板温度场应用到后续未轧道次的辊缝修正计算中。
And the corrected plate temperature is used to adjust the gap setup values.
同时分析了实时轧制力和辊缝数据的处理方法对厚度计算的影响。
The influence of data treatment method for measured force and gap and plate crown on gauge calculation is also analyzed.
GEL7511能控制辊缝调整的位置，发出起动、停止开关信号。
The position controller GEL7511 can control the position of roller seam adjustment, the switch signal of start and stop.
与同类模型相比，该模型直接表达出轧机出口厚度与多个机架辊缝的关系。
Compared with the same models, it straightway reveals the relation of exit gauge and gaps change of each stand.
遥控调整辊缝锥度和动态轻压下的应用，也能满足瞬间浇铸条件的特殊要求。
The roll-gap taper isremotely adjusted and with the application of dynamic soft reduction the special demands for transientcasting conditions can also met.
文中介绍了作者研制的连铸导辊辊缝和椭圆度测量装置的工作原理及测头结构。
This paper introduces the operation principle of the author developed equipment for measuring roll gap and ellipticity of the guide roller in continuous caster.
结果表明：锁定轧机弹跳量的AGC系统优于锁定轧制力和辊缝的AGC系统。
The result is that the AGC system of locking mill elastic extension is better than that of locking roll-load and mill gap.
结合现场实际，验证了模型的准确性，为在线计算出口辊缝提供了思路和依据。
Combined with practical situation, the model accuracy was verified, further the model calculation can lay solid foundations for online calculation of roll gap.
并基于不同条件的计算结果，回归出轧辊凸度变化对辊缝设定影响的计算模型。
The mathematic model of the influence of roll crown variation on gap setting can be got by regression based on lots of calculation results.
板材轧机上一对带特殊辊型的工作辊轴向相对移动时，可改变辊缝凸度，调节板形。
The gap crown between two work rolls of plate mills and the strip shape can be adjusted by axial shifting of the work rolls, both of them have a special contour.
基于此特性，提出中厚板电-液联合辊缝设定新方法?无回缩变精度快速辊缝设定法。
Then a retraction less variable precision gap setting method was put forward based on the characteristic of plate gap setting.
多功能辊缝检测仪是可以自动测量机连铸机辊缝、导辊旋转率等物理参数的计算检测设备。
The Caster Strand Monitor (ROLL CHECKER) system is a measuring device for automatic measurement of the physical parameters of continuous casting machines.
介绍了莱钢中小型轧钢车间轧机采用ABBMASTER系统进行辊缝调整的控制方法。
This paper introduces the controlling method to do roll gap regulation used of ABB MASTER system on medium small section mill of Laiwu iron and steel group co.
系统采用微机进行控制，因此可靠性高，测量准确，检查辊缝方便，可改善连铸钢坯质量。
Its control system utilizes microcomputer to control, so the results are of high reliability and measuring accuracy, handy to inspect and able to improve the quality of continuous casting.
研究了不同宽度和厚度下工作辊弯辊力对辊系变形、辊缝形状及轧件出口厚度的影响规律。
The influence of work roll′s bending force on roll′s bending deformation, roll gap geometry and exit thickness is investigated under the conditions of different width and thickness of sheet.
轧制压力的计算考虑了奥氏体再结晶变化的修正函数，使力能预报及辊缝预设精度明显提高；
The calculation of the rolling poweradopts to consider the variety of the recrystallization in austenite the correction function, improve the accuracy forecast of power and energery;
通过设计双辊铸轧液压A GC系统来调节辊缝间隙，提高其控制精度、响应速度和稳定性。
Twin-roll casting hydraulic AGC system is designed to adjust the gap between double rollers and improve it's control accuracy, response accuracy and stability.
提出一种新型线性变凸度工作辊辊型即lvc辊型，这种辊型实现了辊缝凸度调节与板宽成线性化。
A new work roll contour is advanced which is a linear variable crown (LVC) roll. This roll contour can realize linear ratio of gap crown and strip width.
提出一种新型线性变凸度工作辊辊型即lvc辊型，这种辊型实现了辊缝凸度调节与板宽成线性化。
A new work roll contour is advanced which is a linear variable crown (LVC) roll.
文章简述了轻压下技术的基本原理，并详细介绍了全程辊缝控制轻压下技术在梅山炼钢厂的应用情况。
The principle of soft reduction technique are briefed and the application of roller gap soft reduction technique in Meishan continuous casting are analyzed and discussed.
位移传感器的安装结构是否合理，直接影响轧机液压辊缝控制系统的分辨率、控制精度、响应时间和维护。
The installation of position transducer in hydraulic AGC cylinder has direct effect on the resolution, accuracy control, response time and maintenance of the hydraulic AGC system.
位移传感器的安装结构是否合理，直接影响轧机液压辊缝控制系统的分辨率、控制精度、响应时间和维护。
The installation of position transducer in hydraulic AGC cylinder has direct effect on the resolution, accuracy control, response time and maintenance of the hydraulic AGC system.
应用推荐