为此人们研究了许多功放的线性化方法如功率回退法、前馈法、负反馈法、LINC法和预失真法。
For this purpose, a lot of linearization methods have been investigated including back-off, feed-forward, feedback, LINC and pre-distortion.
从并联电压负反馈的角度，对输入电阻和输出电阻给出了下列4种方法的定量讨论。
From the negative feedback aspect of the parallel voltage, this paper quantitatively discusses input and output resistances by employing 4 methods.
本文还选择了频率应和负反馈放大器稳定性判别中的一些实际问题，作为这种方法应用的实例。
As a practical example a frequency response and stability judgement of an amplifier with negative feedback are chosen to show the use of this method.
本文讨论负反馈放大电路的一种分析方法——节点导纳矩阵分析法。
This paper gives the discussion on a kind of analysis method, Node Admittance Matrix method, for negative feedback amplifying circuits.
本文对模拟电子技术课程中有关“反馈”的判别方法，诸如正、负反馈，电压、电流反馈以及串联、并联反馈等做了详细的分析比较。
The determinant method of feedback, such as positive feedback and negative feedback, voltage feedback and current feedback, series feedback and parallel feedback, etc.
该方法将实际输出电压和期望输出电压的比较偏差作为负反馈加到下一个采样周期的开关调制函数矩阵中。
The discrepancy between the actual output voltage and expected output voltage of the matrix converter is calculated and added to the switch modulation matrix in the next sampling period as feedback.
提出采用超前校正和负反馈校正提高电流放大器输出电流响应速度方法。
Two kinds of methods such as lead net rectification and negative feedback rectification are proposed, which can increase the output current speed of the current amplifier.
本文讨论可控硅电压负反馈调速系统中电压调节器的设计和计算方法。
This paper deals with the design and calculation method of the voltage regulator used in the SCR regulating speed system with voltage negative feedback control.
目前高等院校在模拟电子技术课程中对于负反馈放大电路稳定性进行分析时，一般采用波特图的分析方法。
The stability of feedback of amplifier circuit is often analyzed with bode in Simulation Electron and Technology in the advanced institutes.
目前，方框图法是被广泛使用的分析负反馈放大电路的方法。
The block diagram method is widely used to analyze the negative feedback amplifier at present.
详细阐述了使能电路和负反馈支路的设计方法。
The design of the enable circuit and the negative feedback circuit is described in detail.
本文介绍了用计算机分析负反馈放大器稳定性的方法，给出了用BASIC语言编写的计算程序。
A method for stability analysis of negative feedback Amplifiers by using microcomputer is presented in this paper. The computer program in BASIC Language is proposed.
本文通过三种负反馈类型的具体例子同时介绍了两种分析方法，即方框图法和等效电路法。
In this paper, two methods of analysis, the block diagram method and the equivalent circuit method, have been introduced simultaneously with specific examples of three negative feedback types.
在研究减少放大器失真方法时他发明了负反馈放大器。
While working on a means of reducing amplifier distortion, he devised the negative feedback amplifier.
根据电路原理，应用解析方法导出了四种形式负反馈放大器的输入、输出电阻关系式。
The input and output resistances of a negative-feedback amplifier is calculated by analytic method.
阐述了一种低成本有效标定宽频带负反馈地震计的方法，给出了实际标定结果和数据处理方法。
A low cost and effective calibration method for the broadband feedback seismometer is described, and the results of practical calibration and data processing method are given in this paper.
在原动机模拟部分，采用电枢电流负反馈加转速负反馈的方法对直流电动机的机械特性进行改造。
In the part of prime mover simulation, the technique of armature current feedback plus speed feedback is adopted to alter the mechanical character of the DC electromotor.
提出了降低负反馈以补偿这些影响的原理及实现方法。
The principle and related technique are also presented to Compensate the finite gain effects of op amp by diminishing negative feedback.
实验中采用直接负反馈和趋势预测反馈控制方法，对智能梁结构进行了有效的振动主动控制，得到了良好的效果。
The experiment makes the effectual vibration active control of the intellective girder structure by means of direct negative feedback and tendency forecasting fee…
为了解决启动期间压力增长过快和非线性问题，提出了基于压力斜率截止负反馈的模糊控制方法。
In order to solved the problem of ever-increasing during the start period and the non-linearity characteristic, the fuzzy controller based on the slop cut-off negative feedback of stress was proposed.
采用脉宽调制型控制方法，对采集到的电流信号进行负反馈，通过PI调节控制脉宽调制专用芯片sg3525的输出，以达到控制焊机外特性的目的。
Acquired current signal were inverse feed backed with PWM, then, output of the chip SG3525 were controlled through PI regulator. As a result, the external characteristic was controlled.
采用脉宽调制型控制方法，对采集到的电流信号进行负反馈，通过PI调节控制脉宽调制专用芯片sg3525的输出，以达到控制焊机外特性的目的。
Acquired current signal were inverse feed backed with PWM, then, output of the chip SG3525 were controlled through PI regulator. As a result, the external characteristic was controlled.
应用推荐