应用X 射线衍射（XRD）、扫描电子显微镜（SEM）、能谱（EDX）和红外光谱（FTIR）等分析手段对试样的相组成、形貌、成分、价键结构等进行了分析；
XRD, EDX, SEM and FTIR were used to characterize the structure, composition, morphology and chemical bonds of the samples.
用扫描电子显微镜和能谱仪对钨和铜以及不锈钢的热等静压焊接试样的焊接界面进行了分析研究。
The SEM and EDS were used in this paper to analysis the welding interface of the specimens of tungsten and copper, copper and stainless steel made by HIP welding.
通过偏光显微镜和反光显微镜观察试样釉层的显微结构，发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。
The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer surface of luster glaze.
用扫描电子显微镜(SEM)观测试样的断裂表面，对产生于若干特殊损伤类型的AE信号进行了鉴别。
The fracture surfaces of the specimens were observed by a scanning electron microscope (SEM). The AE signals were distinguished as being released from (several) special types of damage.
用光学金相显微镜和扫描电子显微镜对SWRH72A盘条拉拔断裂试样进行一系列检验分析。
A series of examinations and analysis have been made on the ruptured samples of the SWRH72A wire rod by way of optical metalloscope and scanning electron microscope (SEM).
用会相显微镜、SEM和TEM观察了真空烧结、低压烧结试样的显微结构。
The microstructure of rods sintered in vacuum and by sinter-HIP was investigated by metallographic microscope, SEM and TEM.
在显微镜下观察试样，硬度试验可保证焊接工艺能提供适当的硬度。
Observed under a microscope, the test assures that welding procedures provide proper hardness.
采用X射线衍射和透射电子显微镜研究了试样的显微结构。
The microstructure was investigated by X-ray diffraction and TEM analysis.
利用光学显微镜和数码相机对凝固试样的宏观及微观组织进行观察。
The macrostructure and microstructure of the solidified samples was observed by digital camera and optical microscopy, respectively.
用金相显微镜和SEM观察了试样铸态微观组织形态，测定了奥氏体晶粒尺寸以及奥氏体晶粒内马氏体板条束个数和马氏体板条间距。
Then the morphology was observed by optical microscope and SEM. The grain size of austenite, the number of martensite in austenite grains and the spacing of the lath martensite were measured.
测试样需用起球评级视镜、灯箱或类似箱内与标准起球图片比较评级。
Test samples required Pilling rating endoscopy, bollards, or similar box with the ball with the standard picture comparison rating.
采用扫描电子显微镜和光学显微镜观察了热轧板在冷弯过程中开裂试样的断口形貌并进行了成分分析。
A hot-rolled plate cracked during cold bending process. Scanning Electron Microscope and Optical Microscope were used to investigate the cracked plate.
本文中应用了偏光显微镜、扫描电子显微镜和X射线衍射仪分别对试样的组构特征及扁平颗粒的定向排列特征作了观察和测定。
Polarization microscope, scan electronmicroscope and X ray diffractometer are applied separately to view and determine the fabric characteristics and orientated range of flat particles in samples.
通过偏光显微镜和反光显微镜观察试样釉层的显微结构，发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。
The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur…
并利用金相显微镜、扫描电镜（SEM）和显微硬度计分析了冲击成形后试样组织结构和表层硬度的变化。
The varieties of the microstructure and the surface hardness of the titanium alloys sheet after the deformation are analyzed by the metallography microscope, SEM and the microsclerometer.
结果HCIF试样与对照试样相比，镜下骨板、骨单位组织结构无明显改变，而骨基质伊红染色明显变浅；
Results The microscope show that structure of bone plank and bone unit is not change, and Bone matrix staining obvious shallow Eosin Y;
结果HCIF试样与对照试样相比，镜下骨板、骨单位组织结构无明显改变，而骨基质伊红染色明显变浅；
Results The microscope show that structure of bone plank and bone unit is not change, and Bone matrix staining obvious shallow Eosin Y;
应用推荐