并且介绍了硬件电路和软件的设计。
And also it introduces the designs of hardware circuit and software.
概述了控制系统的电源电路、驱动电路、显示电路与软件设计及信号采集的方法。
The power supply circuit, driving circuit, display circuit, software design and signal collection of the control system are outlined.
通过应用该软件观察虚拟结果是否满足设计要求，这在实际的电路板中是难以做到的。
Through the application of the software to observe whether the virtual results meets the design requirements, the work is elusive in actual circuit board.
介绍电子电路实验CAI教学软件的设计，并以示波器为例说明软件在教学中的应用与教学效果。
This article introduced the design of electronic circuit experiment CAI software, and explained its use and effect in experiment teaching by taking oscilloscope as an example.
阐述了该系统的功能及工作原理，并给出了硬件电路的设计及软件流程。
It describes the function and work principle of this system, and presents the design of hardware and software.
本文阐述了系统的结构和工作原理，搭建了直流毫伏表的硬件电路，并设计了软件系统中的数据采集处理和显示部分的程序。
This paper describes the system structure and working principle, to build a DC mV meter hardware and software system design of data acquisition and processing and display part of the process.
论文对系统硬件性能要求以及软件功能进行了分析。进而，设计了系统的硬件电路和软件功能模块。
In the thesis it analyses the hardware performance requirements and the software functions of the system and designs the hardware circuits and the software function modules after analysis.
详细阐述了系统的总体设计方案，给出了界面模块与89c51接口电路，最后介绍了软件设计方法及程序流程图。
This paper detailedly introduces the whole design scheme of the system, the circuit on interface module and 89c51, the method of the software design and program flow chart.
给出了系统电路和系统软件的设计方案。
详细描述了硬件电路的设计，并给出了软件程序框图。
The design of hardware circuit is explicated and the diagram of program is offered.
其中包括了结构设计、传感器及其测量电路设计、控制系统设计及软件设计。
The method includes configuration design, sensor and testing circuit design, controlling system design and software design.
本文介绍了数字式流量计的系统总体结构、系统的硬件电路设计和系统的软件设计。
The system framework, hardware circuit design and software design of digital flowmeter are presented in the paper.
讨论了系统的构成、硬件电路与软件设计。
We will discuss system structure, hardware circuit and software design.
阐述了超声波液位计的测量原理，给出了实用的硬件电路与软件设计方法。
This paper expounds the measuring principle of ultrasonic liquid gauge, its practical hardware circuit and software design method.
介绍一种机械手关节运动的PC机控制方法，它包括步进电机的驱动、硬件接口电路的设计、软件的编程方法。
This paper introduces PC control approach of joint motion of manipulator. This approach includes driving of stepping motor, interface design of hardware circuit and software programming.
通过软件设计和硬件电路的结合，实现了数据采集电路的模块化设计，提高了系统的精度和可靠性。
By combining software design and hardware circuit, the modularization of designing data acquisition circuits is fulfilled, and the accuracy and reliability of the system are enhanced.
介绍了凸轮轴检测仪的原理、硬件电路及软件的设计。
This article introduces the principle, hardware circuit and software design of cam shaft detector.
本文介绍基于CAN总线的电梯控制系统，并对总体方案、软硬件设计作了分析，给出了具体设计电路以及软件流程图。
This paper introduces the control system of elevator based on CAN bus, analyses its hardware and software and provides hardware design and flow chat.
介绍了硬件和接口电路及软件设计。
The hardware and interface circuits and software design are described.
介绍了以DSP为核心具有以太网接口的嵌入式系统的硬件电路组成和软件设计方法。
This paper introduces a method of hardware constitution and software design of embedded system containing Ethernet interface and adopting DSP as its core processor.
最后，设计了变换器的硬件电路和软件流程。实现了以TMS320F 2812DSP芯片为控制核心的样机。
And then, designed hardware circuit and software flow, realized a sample using TMS320F2812 DSP as kernel controller.
论述了基于SJA1000的CAN总线的硬件接口电路的设计、芯片的选择、软件设计及CAN通信的实现。
The design of CAN bus hardware interface circuit based on SJA1000, the selection of chips, the design of software and the realization of CAN communication are expatiated.
对检测装置的元器件选择、硬件电路设计、软件设计等作了详细说明。
The choice of components and the design of software and hardware were explained.
本文描述了软件设计、接口电路设计以及抗干扰研究等。
This paper gives description of the software design, the interface circuit design and the study on antijamming, etc.
提出了计数接口电路的硬件和软件设计方法，并进行了电路调试。
The hardware and software design methods of the counter interface circuit were put forward. And the circuit debugging has been carried on.
在本次论文中，给出了控制系统的主电路图及软件设计。
At the present This thesis has the system's scheme of hardware main circuit diagram and software design.
详细介绍了DDS算法和硬件设计原理，给出了电路原理图，软件设计原理及流程图。
This article introduces the algorithm of DDS and the principle of hardware design in detail and gives out the circuit diagram, the principle of software design and the flow chart.
详细介绍了DDS算法和硬件设计原理，给出了电路原理图，软件设计原理及流程图。
This article introduces the algorithm of DDS and the principle of hardware design in detail and gives out the circuit diagram, the principle of software design and the flow chart.
应用推荐