判定硬件的设置，特别是人工设定开关的状态。
To determine the arrangement of hardware, in particular a manually set switch.
可根据性能参数检测要求，扳动相应的功率设定开关，任意组合、设定放电功率。
You can combine any of the discharge power according the requirements of performance parameters, setting corresponding power switches.
没有复杂的拨盘或者开关，只有一个很直观的切割功能，可以自动根据需要的钻孔深度调整设定。
No complex dials or switches – just an intuitive slide mechanism that automatically adjusts settings based on the desired depth of drive.
支持用户分组细分的同时，还设有权限开关，管理员可选择为整个组织或某一分组设定服务权限。
Users can be grouped in subdivisions while the administrator has the option to turn the service on or off for the entire organization or for a subdivision.
系统局端控制器软件，具有用户权限管理、通信参数设置、路灯开关时间设定及修改等功能。
The software of its local controller is provided with functions such as user authority management, communication parameter setup, and street lamp on-off time setting and change.
采用优质电子元件组装，主回路设有多重保护；照明开关、喷漆、升温喷漆、烤漆温度、时间设定、故障指示灯。
Control system: lighting switch, spray paint, spray paint of temperature, drying temperature and time setting, emergency stop, limit the warm, failure alarm.
用专用电机带动卷帘中心轴转动，达到卷帘开关，当转动到电机设定的上下限位时自动停止。
Use special motor to drive the rolling center shaft to rotate, to achieve the shutter switch, when the motor is set to the upper and lower limits automatically stop.
该断路器通过拨码开关完成整定电流、脱扣时间、瞬动倍数等参数的设定。
Through dial switches the circuit breaker can set rated current, tripping time, instantaneous multiple and so on.
对开关设备和断路器继进行设定、检查是否配合正确。
Test and set switch gear and circuit breaker relays for proper coordination.
将主配电板上开关设定在自动位置，试验机组没有负载进行。
Set the switches on MSB to 'Auto' position. Generator is to be tested under no load.
该电路具有既能将负载电流限制在设定值以内，又能控制限流工作时功率管的开关频率等特点。
This circuit has both characters of restricting the current within the giving value and limiting the switching frequency of MOSFET operating on current limited condition.
电脑控制系统：设定时开关自动恒温超温报警等功能。
Computer control system: when setting the automatic constant temperature switches etc. Function.
照明开关、喷漆、升温喷漆、烤漆温度、时间设定、故障指示灯。
Lighting switch, spraying, heat sp raying, baking, tempe rature controller, time setting, failure indicator.
当水温达到设定的温度时，温控器将自动关闭加热棒电源，因此开关灯也随之关闭。
The thermostat will automatically shut off the heating element when the selected operating temperature is reached, thus the light will turn off as well.
修理了一个被冻结的申请虫当开关画设定页。
Fixed a bug of application frozen when switch to Picture Settings page.
单机自动控制由操作面板进行开关设定，由PLC自动执行。
Automatic control of individual machines is set by a switch on the face plate of operation desk and implemented by PLC automatically.
说明振动开关的设定值在调试时可以调整到最大灵敏度。
Note Set point for vibration switch is adjusted to maximum sensitivity during commissioning.
它是一台由开关和继电器控制的，必须手工设定。
It was controlled, however, by switches and plugs that had to be manually set.
以OMRONCPM1A为例，介绍了用模拟输入电位器、拨码开关和按钮等方法改变定时器的设定值。
Take OMRON CPM1A as an example, the changing setting value methods in which we use analog input potentiometer, dial switch and push-switch are introduced.
此开关经工厂设定但可现场调节。
灵活的定时设定使得定时开关控制更方便和实用。
Timing flexible timer switch control Settings allow more convenient and practical.
其提供1微米的重复精确度，这些精确的接触开关专门设计用来设定参考点，检查公差，监测，计量和校准工作。
Offering 1 micron repeat accuracy, these precision contact switches are designed for setting reference points, checking tolerances, monitoring, gauging and calibrating tasks.
新增操作手势osd的开关于系统设定之中。
Added the operational gestures OSD option in system Settings.
开关类似于模板中的可选部分，只出现在开关设定的情况下，如果开关没有设定，开关标记的中间部分模板将不会被显示。
Switches are like "optional" parts of the template. They only appear if the switch is set. If the switch is not set, it's simply not shown.
对张力控制微处理机面板上开关进行初期调整，本调整目的在设定铝卷适当的张力值。
Switch initial adjustment for the tension control on the MPU panel to enact the appropriate tension value for the Aluminium coil.
当温度达到设定的档位时，打开蒸汽开关按键，前、后或左、右推动蒸汽熨斗，此时有蒸汽产生。
When the temperature achieves set shift, a steam switch button is turned on, the steam electric iron is pushed front-and-back or left-and-right, and steam is generated at this point.
仪表设上、下限二位开关型接点装置，在压力达到设定值时发出信号或通断控制电路，供作业系统自动控制或发讯用。
Instruments based on the lower limit of two switch-contact device, the pressure to set a signal or when the value of on-off control circuit for the operating system's automatic control or the use.
仪表设上、下限二位开关型接点装置，在压力达到设定值时发出信号或通断控制电路，供作业系统自动控制或发讯用。
Instruments based on the lower limit of two switch-contact device, the pressure to set a signal or when the value of on-off control circuit for the operating system's automatic control or the use.
应用推荐