根据输油泵的关键结构参数，按照传统的经验公式进行了输油量的计算校核。
With all the key structural parameters, the fuel flow can be validated according to the traditional experimental equation.
在强度计算的前提下，首先运用欧洲起重机设计规范对结构稳定性进行手工计算校核。
In the strength calculation of the premise, the first use of the European crane design manual on structural stability of the calculation of check.
通过计算校核和有限元分析，证明该优化设计得出的参数方案比传统设计得出的参数方案更加合理。
According to finite element analysis, calculation and modification, the results show that our optimized parameter setup works better than those traditionary ones without optimizing.
通过结构分析和计算校核，本次研究的烟草移栽机行走机构工作稳定可靠，在农业领域方面具有良好的应用前景。
Check through structural analysis and calculations, this study of tobacco transplanting machine stable and reliable travel agencies in the agricultural sector has good prospects.
本文将石墨制圆形封头多个点的强度校核进行了总结，提出了作者自己总结的强度计算校核方法，为石墨设备设计人员提供参考。
This article summed the calculation of the strength of the circular head in the graphite chemical equipment, introduced a new method for strength calculation checking.
基于减速器的齿轮、轴、轴承、及其校核，文章给出了设计和计算。
Based on the gear reducer, shaft, bearings, and checking, the article gives the design and calculation.
首先进行强度和稳定性计算，主要进行了筒体、端盖的壁厚计算、水压试验应力校核以及叶轮、轴的强度校核。
First of all, for strength and stability, mainly a cylinder, cover the wall, the water pressure check and impeller stress test, the axis of strength checking.
即主要由履带式行走机构和五自由度机械臂组成，着重对履带式移动机器人的行走能力做了详细的计算和校核。
The Robot is consisted of track vehicle and five freedom degree manipulator. It 'motion ability is analysed by calculation and checking.
运用结构力学的矩阵分析法和计算机对抽芯作业车主体金属结构做了力学分析与计算，进而校核主体金属结构的强度、刚度和稳定性。
Mechanical analysis and calculation of the truck's metal construction are made by the matrix method, and the strength, rigidity and stability of the metal construction are checked.
计算结果表明：校核船体在气泡脉动载荷作用下的总纵强度的同时必须计入波浪载荷的影响，对相关理论研究和工程计算有一定参考价值。
Results indicate that the wave loads must be considered when the hull's longitudinal intensity is checked. The research has value to correlative theory research and engineering calculation.
介绍了PW 200k型转向架空气弹簧复合座的结构特点，对该部件进行了改进设计和强度校核计算。
The structure features of the air spring on PW200K bogies are described. The design improvement and strength checking calculation are made for the part.
接着对减速器的部件组成进行了尺寸计算和校核。
Then the components of the reducer to the size of the calculation and verification.
本文针对这些问题，通过选择合适的缆索力学模型并进行力学分析，得出相关的计算、校核公式。
So this paper aim at these questions, though choose suitable mechanics model of cable and analyze the model to educe correlative formula of calculate and validate.
通过封闭环尺寸及公差计算，计算并校核余量及余量公差。
The closed loop dimension and tolerance is calculated in order to calculate and check allowance and allowance tolerance.
本文再一次用内特性法针对现场各种试验情况进行了校核计算，获得了与实测值一致的结果。
This paper conducts the check calculation for various field tests and get the results which are found to be coincided with the actual measures.
对所设计的关键结构进行了计算与校核。
并结合某隧道施工中选用的土压平衡盾构机，对关键参数进行了校核计算。
Combining the soil pressure balance TBM selected in certain tunnel construction, the paper makes check calculation to the key parameters.
加固后对建筑物的观测以及力学校核计算都说明了高压旋喷方法对地基补强是十分有效的。
Observation and mechanical check calculation after completion of consolidation shown that high pressure jet grouting method is highly effective for foundation consolidation.
并用有限差分法对瞬态温度场与热应力进行了校核计算，其结果与实测完全吻合。
Verification calculation of transient temperature and stress distributions were performed with the finite difference method, and the results coincided with the measurements.
本文重点介绍了后悬挂缸的设计计算和强度校核。
This paper introduced the design calculation and strength check of rear suspended cylinder emphatically.
它具有设计型、校核型及逐排计算功能。
It has the following functions: design, check and row by row calculation.
系统主要有三大模块：计算与校核模块，数据库模块，绘图模块。
There are mainly three modules in it: the computation and check module, the database module and the drawing module.
采用分布式计算技术，研究并实现了基于集群计算机的保护定值在线校核并行计算方法。
By means of distributed computing technology, a parallel computing method based on the computer cluster for online relay setting check is studied and developed.
按照我国现行规范的规定，作者编制了船舶舱面集装箱及其系固设备受力计算与校核系统计算程序。
According to the present Chinese criteria, the authors have completed a program for calculating and checking the forces acting on containers on deck and their securing devices.
功率谱估计结果可作为暂态保护判据计算和校核依据。
The result of spectrum estimation can be used as the reference of criterion calculation and checkout in transient protection.
文章对井架总体稳定校核所用的计算公式及分析问题的方法和准则也作了介绍。
The formulas used for checking the integral stability of derrick and the method and criterion of analysing the problems arc also presented here.
通过对退锚器工作压力的确定、强度校核、合理计算，选择了活塞承压面积及各液压缸直径尺寸。
Through anchors identified by the work pressure, intensity degree, reasonable terms, choiced piston confined area and the size of hydraulic tank diameter.
通过对退锚器工作压力的确定、强度校核、合理计算，选择了活塞承压面积及各液压缸直径尺寸。
Through anchors identified by the work pressure, intensity degree, reasonable terms, choiced piston confined area and the size of hydraulic tank diameter.
应用推荐