法兰最大允许工作压力应不小于该法兰在使用条件下的计算压力。
The flange maximum allowable working pressure should not be smaller than the computed pressure of this flange in operation.
计算结果表明，轴颈倾斜时，轴承油膜压力分布、最大油膜压力、油膜厚度分布和最小油膜厚度等都有明显的变化。
The results show that there are obvious changes at film pressure distribution, maximum film pressure, film thickness distribution and minimum film thickness when there is misalignment.
采用考虑位移的土压力计算方法计算环向土压力，得出首节管道和后续管节最大土体反力的计算公式。
By considering displacement for calculating circular earth pressure, the maximal earth counterforce formulas for the heading and the latter pipelines are deduced.
本文根据波动压力计算方法推导出了最大许用起钻速度和下钻速度的计算公式。
By using the surge pressure calculating method, in this paper the formulas have been derived which are used to calculate the maximum allowable velocity in pulling and running pipe in borehole.
利用最大应力强度准则，得到了单一螺旋缠绕及螺旋加环向缠绕圆环压力容器爆破压强的计算式。
According to the maximum stress strength criterion, the burst pressure formula for the single spiral and the spiral with hoop filament-wound toroidal pressure vessel were obtained.
本文计算、分析、确定了限压式变量系和差压式变量泵输出功率最大值和节能效率最大值的压力点；
This paper calculates, analyses and determines the pressure point of maximum of ouput power and saving-energy efficiency of differential pressure and Limited pressure variable displacement pump.
分析计算了这个压力差的最大值。
The maximum of pressure difference has been analysed and calculated.
主要利用ANSYS软件对屏蔽泵密封垫的应力进行分析，计算出压力容器管板的最大应力和应变。
The stress for sealing washer of canned motor pump is analyzed by ANSYS software, and the maximum stress and strain of tubular sheet of press container are calculated.
计算了波纹板表面的压力分布，并指出在土壤与农机具粘附系统中波纹形表面摩擦力最大的位置。
For analyzing the adhesion between soil and tillage tools, the profiles of pressure on the wave bulldozing plates were calculated, and we located the position of the maximum friction on the surface.
在压力容器管板的设计过程中，利用ANSYS软件对压力容器管板的应力进行分析，计算出压力容器管板的最大应力和应变，从而为压力容器结构的优化设计提供了充分的理论依据。
In designing the pressure container tube plate ANSYS software is used to analyze the stress of pressure container tube plate in this paper, and the maximum stress and displaced shape are showed.
通过计算套管中注流的能量分散强度，得出了套管中弥散微小气泡的最大尺寸，并采用伯努利方程分析了套管中注流的压力分布。
The maximum size of the bubbles was obtained through calculating the energy dissipation rate of liquid flow in the shroud.
计算分析了注浆压力差随稠度系数、流变参数、裂隙高度的变化情况以及裂隙高度对最大扩散半径的影响。
It was shown that the grouting pressure difference was related to the rheological parameters, consistency coefficient and gap width of grouting. The penetration radius was also affected by gap width.
通过从最大进口压力减去所需要的出口压力来计算压差。
Calculate the pressure difference by subtracting the desired outlet pressure from the maximum inlet pressure.
基于解析几何法导出的最大压力角表达式，导出了偏心凸轮机构和对心凸轮机构的基圆半径和偏距的计算公式。
According to the allowed pressure Angle, this paper determines the disk CAM with translating followers basic circle radius and eccentricity by using the analytic method.
计算一次进给不对称卷板的可行性，如进行最大变形量、最大压力、最大功率和不打滑的验算等等。
The paper also gives the feasibility analysis of asymmetric plate bending under one time feeding cond...
计算一次进给不对称卷板的可行性，如进行最大变形量、最大压力、最大功率和不打滑的验算等等。
The paper also gives the feasibility analysis of asymmetric plate bending under one time feeding cond...
应用推荐