质量体系，生产，法规及其他适当的人员应参加对元器件，装置及工艺设计文档的评审及评估。
Quality system, production, regulatory, and other appropriate personnel should participate in the review, evaluation, and documentation of the components, device, and process design.
对检测装置的元器件选择、硬件电路设计、软件设计等作了详细说明。
The choice of components and the design of software and hardware were explained.
最后对所做的器件用我们所设计的新的控温装置进行了温度特性实验，并对实验结果进行了分析。
At last, we have done temperature characteristics experiment through using our designed new type control-temperature equipment. And we have analyzed experiment results.
由于磁刺激器是高电压、大电流的装置，本文对元器件的选择、设计中的注意事项等关键问题特别进行了阐述。
The paper expatiates key points such as elements choosing and notices in design in particular because magnetic stimulator is high voltage, large current device.
对液晶投影显示系统的偏振器件进行了研究，提出了一种新型偏光转换装置的设计方法。
The polarizing conversion system (PCS) of LCD projection display is studied and a novel method of design PCS is reported.
主要介绍以可编程门阵列器件构成恒流源核心控制电路的设计思路，通过机电自控装置驱动可调变压器实现新的稳流方法，实验证明这一方法是可行的。
A design method of using GAL to make a constant current source is introduced, proving a new method of current stabilization by means of driving regulated transformer by a controlling device.
针对直流电网短路故障时迅速产生的短路电流，利用IGBT器件为核心，设计出一种新型的直流短路电网限流装置并阐述了其工作原理。
As the large fault current occurs in DC power system, the paper makes use of IGBT to design a new type DC fault current limiter.
探测器的设计有：光学器件的设计和选取、电路的设计、采样区大小控制装置和防污染装置的设计。
The detector design consists of design and select of optic parts of an apparatus, circuit design, sampling area control and antipollution device design.
选择、设计实验器件，搭建了用于角膜地形图测量的径向剪切干涉实验装置；
Moreover, the experimental setup of radial shearing interference for human eye corneal topography was established with proper selection and design of experimental apparatuses.
本文介绍了基于总线集成控制技术设计的SOI器件高温环境实验装置的智能控制系统。
An intelligent control system of high temperature environmental test for SOI device is introduced, which is based on the technology of bus integration.
介绍了制冷机中蒸发器和毛细管等管路器件特性参数自动测试装置的设计原理和实施方法。
The design principle and implementation of Autoinstrument for measuring characteristic parameters of evaporator series with capillaries in refrigerator are introduced.
工作时需潜入海底，装置的电气、电子器件之多、空间之狭小是空前解决电磁兼容是设计的关键问题之一。
The device should dive to the sea bottom when working, and there are so many electrical and electronic elements in such a narrow space within the device that this situation is uncommon.
介绍了激光干涉法长度测量的基本原理，提出在不更换和调整系统中光学器件的条件下，实现线位移和角位移—机测量集成装置的设计思想。
The paper introduces the basic principle of measuring displacement with laser interferometer, and gives a designing idea that realizes length measurement and angle measurement on one apparatus.
为了高精度、非接触动态地检测灌浆工程中水泥浆液的密度，采用CR 105型光电倍增管作为感光器件，设计了一种检测装置。
In order to monitor the cement grout density accurately and dynamically in grouting practice, a detection instrument incorporating a CR105 photomultiplier tube as optic sensor was designed.
利用VHDL语言在PLD器件上设计全功能计数控制装置，使其实现计量、显示长度并根据预置数输出控制信号的功能。
A full-function control system of counting is designed on a PLD device using VHDL language. It can measure and display the length and send out a control signal according to the set value.
利用VHDL语言在PLD器件上设计全功能计数控制装置，使其实现计量、显示长度并根据预置数输出控制信号的功能。
A full-function control system of counting is designed on a PLD device using VHDL language. It can measure and display the length and send out a control signal according to the set value.
应用推荐