该机能够机械装料，自动卸料。
The machine is featured by mechanic loading and automatic discharging.
可选装料架及自动送料装置。
矿、煤分层水平装料方式优于垂直装料。
The paralled loading the lay of coal and ore are better than perpendicular.
通过初装料的运行，证明该系统运行良好。
The operation of the first loading indicates that this system is reliable.
炉喉布料挡圈是一种控制布料最简便的辅助装料设备。
However, the distributing ring of furnace throat is the most simple auxiliary charging device for distribution control.
带压力卸料装置的散装料运货车。带板簧的压力计。径向。
Bulk freight wagons with pressure discharge; pressure gauge with plate spring, radial bottom flange connection.
横向位移受物料形态影响最大，其次是装料高度和斜面倾角。
The main effect affected by material feature is lateral displacement, then the loading height and slant Angle.
此方法特别适用于手工操作来控制螺旋输送机的装料的场合。
This method is suitable to control the screw conveyor in manual loading.
计算机程序可以预测锻模的装料、负载、能量和缺陷的形成。
Computer programs can predict die fill, load, energy, and defect formation.
当必须避免废气与装料接触时，这种炉子需更换一个后式烟囱。
The furnace can alternatively be supplied with a back exhaust when waste gas contact on charge material must be avoided.
同时也讨论了喷煤、风温、铁水硅含量及装料制度对焦比的影响。
The factors for affecting coke rate were discussed such as coal injection, blast temperature, silicon content and charging patterns.
含可燃毒物的压水堆堆芯装料优化是燃料管理优化研究中的难点。
The reloading optimization problem of PWR with burnable absorber fuel is very difficult, and common optimization algorithms are inefficient and have bad global performance for it.
介绍了一种新型的掘进巷道装料设备以及它的工作原理、使用效果。
This Paper introduces a new tunneling feeding installation, principle and using result.
十七火灾发生之前，期间或之后，立即被删除，气顶装料前开始的。
Seventeen fires occurred before, during or immediately after the gas cap was removed and before fueling began.
顺时针转动前单向节流阀手柄，气缸前行速度放慢，装料速度也放慢。
When the level of the front one-way throttle valve is turned clockwise, the forward traveling speed of the cylinder and charging speed slow down.
逆时针转动前单向节流阀手柄，气缸前行速度加快，装料速度也加快。
When the level of the front one-way throttle valve is turned counterclockwise, the forward traveling speed of the cylinder and charging speed increase.
这样，第一个料台首先冷却，然后重新装料，而另一个料台还在加热。
The first base can be cooled, and then re-loaded while the other load is under heat.
主要叙述双料钟式中小高炉炉顶装料设备安装调试的方法、步骤及要领。
Steps and key points of installation and adjustment of double-bell type top charging equipment in middle and small blast furnaces are introduced.
安装料压传感器，可避免漏换和错换，并可降低熔体压力30 %以上。
The filter equiped with a melt pressure sensor could avoid wrong change and decrease the melt pressure by 30 %.
本文介绍5MW低功率堆(5mwLPR)首次装料及首次临界试验。
The first criticality experiment of 5mw Low Power Reactor (LPR) is described.
在实际装料时，不同密度、粒径及形状系数的颗粒在料面上的落点也各不相同。
In practice, the landing points of particles are not the same because of their different density, size and shape.
穿流式烘箱比平流式干燥能力大，每层物料装料厚度为平流式烘箱的三倍以上。
Compared to traditional horizontal chamber dryer, its capacity of drying is larger. the thickness of raw materials each layer can be over three times.
接收码头区域应当是硬面，拥有合适的排水区域，并且应直接通往蒸煮锅装料区。
The receiving dock area shall be hard surfaced, shall have suitable drainage and shall lead directly to the cooker charging area.
装料实测为建立更加切合实际的无钟炉顶布料工艺方案和验证布料方程奠定了基础。
Burden distribution experiments provides practical and reliable foundation to build a more suitable plan of burden distributing of bell-less top and to verify the burden distribution equation.
但由于装料、卸料、起动等操作占用时间较多，因此设备利用率低，生产效率也不高。
But because the loading, unloading, starting operation takes more time, so the equipment utilization rate is low, the production efficiency is not high.
这种液体包装专用料也可以代替LDPE重包装料制成重包装袋，用于包装各类材料。
This special polyolefin liquid packaging resin may replace LDPE heavyduty packaging bags and can be used for the package of all kinds of materials.
装桶由半自动化装料机和有关节的装料臂共同完成。有关节的填充臂能依次达到四个桶。
Filling barrel was accomplished by semiautomatic filler machine and jointed filling arm, and the filling arm can reach the four barrels in turn.
装桶由半自动化装料机和有关节的装料臂共同完成。有关节的填充臂能依次达到四个桶。
Filling barrel was accomplished by semiautomatic filler machine and jointed filling arm, and the filling arm can reach the four barrels in turn.
应用推荐