多种继电器输出方式。
控制旁路接触器的接点是无源继电器输出点；
The joints of control bypass contactor passive relay output points;
该继电器输出，是春天偏见总和，与范围螺丝集，加上气动输入信号。
The output of the relay is the sum of the spring bias, set with the Range Screw, plus a pneumatic input signal.
电脑板采用继电器输出，无需中间继断器减少了故障点，维修检测方便。
Relay output is used for the computer panel, medial relay is not necessary, reduced malfunctions and make maintain and inspecting convenient...
这种气动继电器输出提供了压力，表示输入信号压力加上预设的偏见高输出流量。
This pneumatic relay provides high output flow at an output pressure that represents the input signal pressure plus a preset bias.
同时对继电器类型的输出装置进行了分析和研究，设计出适合本系统的继电器输出电路。
Meanwhile, the relay is one of the output devices. After analyzing its characteristic, we have worked out the corresponding output circuit.
飞兆半导体的1500a型继电器输出是春天偏见总和，与范围螺丝集，加上气动输入信号。
The output of the Fairchild Model 1500a relay is the sum of the spring bias, set with the Range Screw, plus a pneumatic input signal.
SIL2输出量—SIL 725安全传感器具有普通的安全继电器输出量，SIL2也符合。
SIL2 outputs - The SIL725 Annunciator has common safety related relay outputs which are SIL2 compliant.
由单片计算机控制的计数器自动产生通1秒停4秒的信号，使5路继电器输出带动电喇叭轮流通电。
By single chip computer control of counter automatically generate tong 1 second stop 4 seconds of signal, make no. 5 relay output drive electric horn turns electrify.
大多数开关主机都可通过触发输入进行外部触发，并且在继电器触点稳定之后可输出一个触发脉冲。
Most switch mainframes can be triggered externally via the trigger input and can send an output trigger pulse when the relay contacts have settled.
飞兆半导体的21型是一种可调比气动继电器，即输出的压力信号的压力比是无限可调。
Fairchild's Model 21 is an adjustable ratio Pneumatic Relay, whereby the ratio of output pressure to signal pressure is infinitely adjustable.
只有A/C扩大器上的电压是来自输入端的正确电压时，初级输出（即A/C压缩机继电器）才会被激活开启。
It is only when the correct voltages are applied to the A/C amplifier from the key inputs that the primary output (the A/C compressor relay) will be energised.
当主机中的扫描卡被全部用完之后，这些输出可用来控制少量的外部继电器。
These outputs can be used to control a few external relays in case the scanner CARDS in the mainframe are already committed.
正常状态下，残留在泄露和过热感应器和各自的输出继电器上的电阻会被释放。
Under normal conditions the resistance remains between the leakage and over-temperature sensitivities, and both output relays are de-energized.
在500毫安，NPN达林顿输出的积分瞬态抑制二极管，是适合于继电器，螺线管和其他感性负载使用。
The 500 mA, NPN Darlington outputs, with integral transient-suppression diodes, are suitable for use with relays, solenoids, and other inductive loads.
改变了继电器控制系统中机械式的鼓形控制器或凸轮控制器步数和输出点数有限、体积大、重量大、成本高的缺点。
It changes the disadvantage that drum or CAM controller in relay control total steps, output points are limited, large volume and weight, high costing.
设计和实现了一种采用工控机与温度模块、PWM输出卡、固态继电器及相关控制电路搭建的计算机电阻炉温度控制系统。
Temperature computer control system of a resistance furnace is designed with industry person computer (IPC), temperature input module, PWM output card, solid state relay(SSR) and interrelated circuit.
外围输出控制系统由发光二极管、继电器、数字开关等模拟外围设备，控制其它的弱电设备和一般的强电设备。
The periphery output control system is composed of analog peripheral device such as LED, relay, digital switch etc, to control the other weak-current devices and general heavy-current devices.
门机运行到该位置输出“指定位置”继电器信号。
When the door motor run to the position, it output pointed position relay signals.
门机运行到该位置输出“门开齐”继电器信号，门机开始开门推进。
When the door motor run to the position, it output door open fully relay signals and start to open door pushing.
传感器输入量和继电器的输出量可由用户定制。
接下来的检测工作。就是耍对继电器的电源输出状况进行测量。
The next testing. Is playing on the relay the status of the power output measurement.
具备特定功用的控制输入和可编程输出继电器。
Control inputs and programmable output relays for specifics functions.
操作员决定所要求的体积，然后激活输出继电器，决定进料时间。
The operator determines the volume required to activate the output relay and determines the duration of the feed event.
门机运行到该位置输出“门关齐”继电器信号，门机开始关门推进。
When the door motor run to the position, it output the relay signals of "door close fully" and the motor start to close door pushing.
任何错误，在系统出现，就会启动一个单独的输出继电器。
Any error that appears in the system will activate a separate output relay.
每种电源都带有延时继电器，它在电子管进入稳定工作状态之前使输出静音。
Each supply has a timed relay that mutes the audio output until the tubes stabilize.
该型号25逆转继电器是专为应用程序要求的输出，等于减去一个变量信号压力手动预设弹簧负载。
The Model 25 Reversing Relay is designed for applications requiring an output that equals a manually preset spring load minus a variable signal pressure.
利用工控机控制继电器选择不同的充放电电容，就能调节输出陡脉冲的脉宽。
Controlling relays to choose different capacitors with ICC, the width of output pulse can be adjusted.
利用工控机控制继电器选择不同的充放电电容，就能调节输出陡脉冲的脉宽。
Controlling relays to choose different capacitors with ICC, the width of output pulse can be adjusted.
应用推荐