交叉换位技术广泛应用于高频变压器绕组设计。
Interleaving skills are frequently used in the design of windings of high-frequency transformers.
采用大、小绕组设计，保证大、小电流输出都能稳定输出。
Big and small winding design ensures steady output of both big current and small current.
本文较系统地介绍了采用多层绕组设计单绕组双速电机的方法。
In this paper, a method is developed for designing two-speed single-winding induction motors with multi-layer winding.
根据分析结果，提出一些保证绕组短路强度的措施，为变压器绕组设计提供参考依据。
According to analyzing results, a few measures are given to ensure short-circuit strength of windings and referential rules are provided for design of transformer windings.
在内外定子主要尺寸、磁路结构、绕组设计讨论的基础上，完成了该电机的电磁设计。
After discussing stator size, magnetic circuit and winding design, the electromagnetic design of the motor was presented.
介绍了环氧树脂浇注干式变压器无填料绕组浇注的工艺特点、材料的选择和配方设计，提出了浇注过程中应注意的事项。
The formulation design, processing characteristic and material choice of winding without filling in epoxy resin cast dry-type transformer are introduced. The warnings in cast process are presented.
改良输出变压器还是基于麦氏的原始想法，也就是说，变压器还是按照传统的推挽输出设计，而且初级绕组具备中央抽头。
The output transformer USES the original idea presented by McIntosh, that is, the transformer is designed for a conventional push-pull output and the primary windings are halved.
介绍了常用的不同结构及拉力可以调节的变压器绕组导线张紧装置的结构设计及应用。
The application and structure design of common adjustable tensile force tension devices for winding conductor of transformer with different structure are presented.
设计了相应的定子绕组结构。
本文借助计算机对多极正余弦第三型绕组进行设计计算。
In this article multipolar resolver sine-cosine third winding is designed and calculated by computor.
论文以材料费用为目标函数，铁心长度及绕组匝数为变量编制了计算程序，对单相电机进行了优化设计并给出了计算结。
It selects material cost as target function, core length and winding turns as variables to develop program for optimization design of single phase motors.
文章讨论了这些设计方式对绝缘系统包括固体绝缘和绝缘液体的影响，并且对绕组和油道进行了热分析。
This paper discusses the influence of the design mode on insulation system including solid insulation and insulation liquid, and carries out the heat analysis of winding and oil duct.
为此需用精确设计的正交绕组加以补偿。
For this reason, a well designed orthogonal winding is needed.
设计一种基于反激式同轴多绕组输出均衡电路，实现对多个串联单体的快速有效均衡。
One kind of equalization circuit based on CWT (coaxial windings transformer) was designed to achieve the destination of fast equalization on series connected ultra capacitors.
本文介绍了用单层绕组和换相法设计远极比变极电机的方法。
The paper presents a method to design wide-ratio pole-changing motor by using single-layer winding and phase changing.
本论文提出了一种反向法变极绕组的系统设计方法和最小对称槽号组的概念。
This paper proposes a systematic method in the design of pole-changing windings based on reversing coil techniques and the concept "the minimum symmetric coil groups".
文章介绍了南芬露天矿295B电铲提升系统836千瓦主发电机大修中对损坏丢失的绕组数据的恢复设计。
The paper introduces a recoverable design for the lost information of generator winding during heavy repair to the elevation system of the shovel 295B, in which the 836kw generator gets out of order.
一般电路设计对磁性材料和绕组电流相互之间的电磁相互作用研究较少，而这对逆变器快速瞬态性能有重要影响。
To the general circuit design it is no need to research the interaction of the transformer magnetic material and coil current, but it is very important to the study of transient character of inverter.
本文介绍了偏转绕组结构的设计。
In the paper, the design of deflection winding configuration is described.
提出了无刷双馈电机定子绕组的连接形式及其设计方法。
The connection mode and design method for the stator windings of brushless doubly fed machines is proposed in this paper.
现在电力系统中，变压器设计与选型上出现了一些特殊绕组变压器。
Now some transformers with special connected mode of winding are applied in the electrical engineering.
只有发电机设计与继电保护密切合作，才有可能完成定子绕组的优化设计。
The close cooperation between generator design and protection can only be a way to do optimization design for generator stator winding.
探讨了其定子绕组和转子绕组的设计方法。
The designing methods of its stator winding and rotor winding are also discussed.
一旦电机达到接近设计运行转速，离心开关开始动作，关断启动绕组与电网之间的连接。
Once the motor reaches near design operating speed, the centrifugal switch activates, opening the contacts and disconnecting the startup winding from the power source.
分析集中式绕组的无刷直流电机各结构设计参数对磁场的影响，尝试求取、分析空载漏磁系数，讨论如何削弱定位转矩。
The influence of a centralization winding brushless DC motor structural design parameter and magnetic field were analyzed, and a way to achieve the fix position angular force was brought out.
介绍了三相绕线型异步电动机转子波绕组排列图自动生成系统的设计方法。
The paper introduces the design method of auto creating system of arrangement diagram for wave winding of rotor for three-phase asynchronous motor.
输出电压的特点是根据插槽潜力的星图，分析和电枢绕组的设计约束。
Characteristic of output voltage is analyzed according to the star graph of slot potential, and the design constraints of armature windings are provided.
提出了一种印制绕组电机导条形状的优化设计方法，由此可以获得最大的反电势系数。
An optimization method for designing the conductor shape of printed circuit motor to attain Max.
提出了一种印制绕组电机导条形状的优化设计方法，由此可以获得最大的反电势系数。
An optimization method for designing the conductor shape of printed circuit motor to attain Max.
应用推荐