使用数据采集系统实时采集试验过程中的压力、流量数据,同时对筛管防砂后的流体采样,并进行粒度分析。
It can collect the pressure and the flow by da (data acquisition) system during testing, also can sample and analysis the grain size of the flow after controlled sand.
对小型锤片式无筛粉碎机进行粉碎试验,分析比较了影响加工粒度的因素。
According to the experiment of minitype hammer no-sieve disintegrator, we analyze the effect factor of machining granularity.
试验结果表明,经过哈氏可磨性测定仪后,各煤种的工业分析都发生了不同程度的变化,而煤粉破碎后的粒度分布取决于煤种的煤化程度,而与煤种的可磨性指数相关性较小。
The results(indicated) that the approximate analysis of the pulverized coal changed to different degrees, and the particle size distribution mainly depended on the coal rank but not the HGI.
通过对洗矿作业的查定及产品粒度组成和回收试验结果的分析,论证从溢流中回收流失的锰矿物的必要性和可能性。
After checking the whole ore-washing process, and analysing the particle size and the experiment results, this paper shows the necessity and possibility of recovering the lost Mn.
结果说明激光粒度分析是一种可靠和精确的试验方法,可用于油品的分析。
The results show that it is a reliable and accurate test method and can be utilized for petroleum product analysis.
同时,试验分析了过滤压力、悬浮液质量分数、粒度分布及温度等因素对过滤性能的影响。
At the same time, factors such as filtration pressure, density of the liquid, particle distribution and temperatures which affect filtration properties are analysed.
结合铣削镁粉的实际生产,对影响铣削镁粉质量的主要因素进行了分析、试验,提出了控制铣削镁粉粒度和形状的有效措施。
The main factors of affecting milling magnesium powders are analyzed and tested based on actual production practices of milling magnesium powder.
通过定量分析不同粒度水砂纸磨光后在钢试样表面造成的表面质量差异,找到适合不同硬度试验需要的表面质量的具体获取方法。
These methods are acquired via quantitative measurement of surface quality differences caused by water proof abrasive papers with various degree of roughness on the steel samples.
提出了通过显示奥氏体实际晶粒度、裂纹形貌和扩展方式来分析热锻模具型腔表层塑性变形行为的试验方法。
This paper advanced a study method that can observe plastic deformation behavior of surface layer of die cavity by showing austenite grain, size, crack morphology and propagation mode.
经对试验结果分析表明:在其它工艺参数不变的情况下,随着焊接速度的增加,焊缝组织的晶粒度减小。铜管的扩口率增加。
The results reveal that the grain size of welding seam decreases with the increase of welding velocity and the rate of tubes' extension increases under the same technological conditions.
通过操作性能测试、汉诺威电弧质量分析系统测试、硬度试验和磨损试验,研究了金红石粒度对焊条性能的影响。
By welding operating testing, measurement of Hannover arc characteristics analyzer, hardness test and wear test, the influence of rutile particle size on the properties of the electrodes was studied.
通过操作性能测试、汉诺威电弧质量分析系统测试、硬度试验和磨损试验,研究了金红石粒度对焊条性能的影响。
By welding operating testing, measurement of Hannover arc characteristics analyzer, hardness test and wear test, the influence of rutile particle size on the properties of the electrodes was studied.
应用推荐