大多的生成树算法（STA）失败发生由于过多的丢失BPDU导致阻塞端口转换为转发模式。
Most of the Spanning Tree Algorithm(STA) failures occur due to the excessive loss of BPDUs causing the blocked ports to transition to forwarding mode.
然后，借助于研制的精密四端对-单端口转换器，用四端对阻抗测量仪测量单端口电容器容量值；
Secondly, with the aid of developed 4TP-single-terminal-port transform device, capacitance value of single-terminal-port capacitor is measured by 4TP impedance instrument.
针对usbGPRS调制解调器而言，USB - to - serial转换器一般us b端口转换为虚拟串行端口，因此系统其他部分就会将它看作串行设备。
For USB GPRS modems, a USB-to-serial converter typically converts the USB port into a virtual serial port so the rest of the system sees it as a serial device.
正如你所见，NAT路由器将每台计算机的IP地址和端口号都存储在地址转换表中。
As you can see, the NAT router stores the IP address and port number of each computer in the address translation table.
转换创建组件端口和协作角色之间的UML绑定。
The transformation creates UML bindings between component ports and collaboration roles.
转换利用为业务过程所需或提供的服务指定接口的端口来填充所生成的组件。
The transformation populates the generated components with ports that specify interfaces for services required or provided by the business process.
转换还通过端口对组件进行组装，每一个表现界面或者是被服务所提供，或者是被服务所需要。
The transform also populates the component with ports, each representing interfaces either provided or required by the service.
以转换的观点，此服务规范映射到WSDL端口类型，此时这是一个无趣的端口，因为到目前为止还没有操作或消息。
From a transformation point of view, this service specification maps to a WSDL port type, which at this time is an uninteresting port type because it has no operations or messages so far.
选择要转换为MQ消息传递提供程序激活规范的消息侦听器端口，并单击Converttoactivationspecification按钮(图6)。
Select the message listener port to be converted to an MQ messaging provider activation specification, and click the convert to activation specification button (Figure 6).
由于nat路由器现在已经拥有了这台计算机保存在地址转换表中的的源地址和源端口号，它将会在有效期内继续使用同一个端口号进行转换。
Since the NAT router now has the computer's source address and source port saved to the address translation table, it will continue to use that same port number for the duration of the connection.
本设计方案描述了为不同宽度读写数据端口的数据宽度转换，怎样基于FPGA的FIFO实现共有时钟(同步)。
This Design Idea describes how to implement a common clock (synchronous version) for an FPGA-based FIFO for data-width conversion with different-width read and write data ports.
针对会话发起协议（SIP）穿越网络地址转换（NAT）的问题，提出一种基于端口探测的解决方案。
To solve the problem of Session Initiation Protocol(SIP) traversing Network Address Translator(NAT), this paper describes a new method based on port detection.
它内置一个16位高速采样adc、一个内部转换时钟、一个内部基准电压源(和缓冲)、纠错电路，以及串行和并行系统接口端口。
It contains a high speed 16-bit sampling ADC, an internal conversion clock, an internal reference (and buffer), error correction circuits, and both serial and parallel system interface ports.
如果系统需要改变，修正，或者由于疏忽错订了产品，则采用这种套件能够轻易地转换阀门端口连接件。
Allows easy conversion of valve end connections due to system change, modification, or inadvertent misorder of product.
当一个不完美的两个设备之间的接触-例如与热敏传感器和A至D转换器端口-发生时，温度检测有可能成为这样的模式，如下所示。
When an imperfect contact between two devices - for example between the thermistor sensor and the A-to-D converter port - occurs, the detected temperature may become like this pattern, as shown here.
通过端口预测方法实现对称型网络地址转换的穿越。
The symmetrical NAT traversal is achieved by using port prediction method.
在单片机的输出端口接DAC0832进行DA转换，再通过运放进行波形调整，最后输出波形接在示波器上显示。
The output of the machine connect DAC0832 to carry on a DA conversion, again pass operation amplifier to put an end exportation wave-form.
应用能量成形方法，将永磁同步电机控制系统看作二端口能量转换装置，建立了位置伺服控制模型，求取了满足最大输出功率原理的系统平衡点。
The position servo control model of PMSM system is established, and the equilibrium which satisfies the maximum output power theory is derived.
应用能量成形方法，将永磁同步电机控制系统看作二端口能量转换装置，建立了位置伺服控制模型，求取了满足最大输出功率原理的系统平衡点。
The position servo control model of PMSM system is established, and the equilibrium which satisfies the maximum output power theory is derived.
应用推荐