支持全范围的远程管理端口设置。
在侦听器端口设置最大消息值及最大会话并发数。
The Maximum Messages value is set on the listener port, along with the Maximum Sessions concurrency setting.
清单2. minicom串行端口设置菜单。
没有问题的端口设置错误。
因此，大多数BIOS允许将不被使用的端口设置为禁用。
For this reason, most BIOSes allow ports that are not in use to be disabled.
要设置设备端口设置，您必须在安装完成后转到设备属性页。
To setup your device port setting, you will have to go to device property page after installation is completed.
尝试将端口设置为9081，或看一下您的测试服务器设置，以确定正确的端口。
Try setting the port to be 9081 or look at your test server Settings to determine the correct port.
然而，迁移为通道框架要求用于web容器的主机和端口设置必须符合通道定义。
However, moving to the channel framework necessitates that the host and port Settings for the Web container be changed to conform to channel definitions.
您需要在移植节点之前将主题连接工厂端口设置由DIRECT改为QUEUED。
You will, however, need to change your topic connection factory port Settings from DIRECT to QUEUED prior to migrating your node.
对于HTTPProxy和SSL Proxy，都输入localhost，并将端口设置为8008。
For both HTTP Proxy and SSL Proxy, type localhost, and set the port to 8008.
这段简单的代码将在指定的端口设置与指定服务器的连接，然后将命令行中传递给它的文本发送到服务器上。
This simple piece of code sets up a connection with the specified server on the specified port, then sends the text passed to it on the command line on to the server.
此更改将通过所定义的portoffset值修改CommunityEdition中的所有服务的端口设置。
This change modifies the Port Settings for all the services in Community Edition by the defined value of PortOffset.
注意：把Tomcat的HTTP端口设置为8082，这是因为Eclipse已经在使用8080部署cxfWeb服务。
Note: Tomcat's HTTP port is set to 8082 since Eclipse is already using 8080 to deploy CXF Web service.
应该对照主文件或DNS检查服务器文档中 TCPIP端口设置的NetworkAddress条目以确保准确性。
The TCPIP port setting's Network Address entry within the Server document should be checked for accuracy against the hosts file or DNS.
那么该端口推荐的最大设置限度是什么，并且即使有分支，如何将最大会话调高？
What is the maximum recommended listener port setting, and the ramification, if any, for turning up the maximum session to high?
本文介绍如何使用串行通信端口来设置调试环境、如何编译经过修改的内核代码，以及如何开始内核调试。
This article shows you how to set up the debug environment using serial communication port, how to compile modified kernel code, and how to start kernel debugging.
注意：如果您配置了远程CEI服务器，则必须修改CEI选项，以显示远程主机名、R mi端口和安全设置。
Note: if you have configured a remote CEI server, you must modify the CEI options to specify the remote host name, RMI port and security Settings.
这就跟设置hba端口一样，因此按上述步骤进行即可。
It's like setting up another HBA port, so just follow the same steps.
端口定义的缺省设置如表2所示。
全局选项设置使用UDP、udp端口，并配置将要创建的虚拟设备的名称。
The global options set the use of UDP, the UDP port, and configure the name of the virtual device that will be created.
如果您将端口属性的值设置为8080，那么图中就会出现“端口值8080无效”的警告信息。
If you set the port attribute's value to 8080, the "port value 8080 is invalid" warning is shown in the diagram.
优化服务器性能：端口加密和缓冲池设置。
Optimizing server performance: Port encryption and Buffer Pool Settings.
单击Next接受默认的服务器端口和设置。
设置端口号(默认端口为443)。
例如，如果您打开到特定主机的Telnet连接，则目的地端口将被设置为23。
For example, if you open a Telnet connection to a particular host, the destination port will be set to 23.
接受远程服务器的STARTTLS命令之后，Domino使用该服务器的ssl端口的设置来管理会话的验证。
After accepting the STARTTLS command from a remote server, Domino USES Settings for the server's SSL port to govern authentication for the sessions.
对于高级用户，可以按如下所示改变端口号和调试设置。
For advanced users, you can alter the port number and debug Settings like this.
所有相关机器上的代理控制器（DCI的一部分）端口必须设置为缺省值 (10002)。
The Agent Controller (part of the data collection infrastructure) port on all involved computers must be set to the default (10002).
在配置文件创建过程中，安装程序将显示一个面板，通过该面板您可以对version 6.0设置端口分配。
During the profile creation process, the installer will present a panel that enables you to set the port assignments for Version 6.0.
在配置文件创建过程中，安装程序将显示一个面板，通过该面板您可以对version 6.0设置端口分配。
During the profile creation process, the installer will present a panel that enables you to set the port assignments for Version 6.0.
应用推荐