可直接用于对电镀槽,以消除冲洗洒水和烟气洗涤水。
The ET-III-W can be used directly on the plating tank to remove rinse spray water and fume scrubber water.
对电镀化学工程师来说,它是控制电镀槽最有用的工具。
It is among the most useful tools available to the plating chemist for control of plating baths.
电镀是一种在电镀槽通上电流使金属沉 淀在基体上的电化学过程。
Electroplating is an electrochemical process by which metal is deposited on a substrate by passing a current through the bath.
电镀槽液的管理和处理方法是决定电镀厂产品质量和经济效益的重要手段。
The maintenence and treatment of the plating bath plays a decisive part in ensuring product quality and economic benefits of the plating shop.
电镀槽:可承受,储存电镀药水的槽体,一般考虑强度,耐蚀,耐温等因素。
Electroplating trough: bearable, storage solutions, the pilot line chemicals general considerations intensity, corrosion resistant, heat resistance, and other factors.
利用X射线衍射技术,研究了由五种不同电镀槽液所获得的镀锌层中品体的取向。
Crystallographic orientation of electrodeposited zinc in five different electrolytes were studied by means of X-ray diffraction technique.
光亮电镀:在适当条件下,从镀槽中直接得到具有光泽镀层的电镀。
Light plating: in the right conditions, can be obtained directly from the plating slot have burnish of plating coating.
如果过渡段被电镀(倒角和内切槽)将会产生应力集中,造成裂纹。
Plating into a transition (radius transition or undercut) will create a stress concentration that can cause crack initiation.
研究了从焦磷酸盐槽液中电镀锡镍合金的一种新工艺,讨论了一些电镀参数对锡镍合金镀层的影响。
A new technology of tin-nickel alloy electroplating from a pyrophosphating bath was studied. The effect of some plating parameters on the tin-nickel alloy coating was discussed.
本文主要阐述赫尔槽基本原理及其在印制电路板电镀过程中的应用。
In this article, the basic theory of Hull Cell Testing and its application in electroplating process for printing circuit board is explained.
本研究采用动态电解装置直接从电镀生产线的回收槽中循环电解回收铜。
This is a study of recovery of Cu from acidic copper rinse water by mobile electrolysis equipment which is installed on the rinsing tanks of the plating line.
经小槽电镀,获得外观致密均匀,似镜面光亮,结合力强,具有优良的可焊性镀层。
A uniform, compact, bright lustre, good adhosive and excellent solderable coating was obtained by the experimental electroplating.
ABS全自动塑料电镀生产线主要由机架、镀槽、管路、通风、行车、导电系统、阴极移动及辅助设备组成。
ABS automatic plastics electroplating line is composed of frame, tank, pipe, ventilation, conducting system, cathode sweeping and other auxiliary equipments.
本文叙述了化学沉淀法处理电镀锌镍合金废水所得到的污泥回槽利用问题。
This paper presented putting use of the wasted mud residue of plating Zn-Ni alloy to reclaiming bath by chemical deposition method.
在电镀面很小时也可以不用限热槽,但是电镀面很大时就需要小心,因为此时不容易焊接。
You can omit the thermal reliefs when the plane is quite small, but be careful because the pin may be hardly solderable if the plane is too large.
在电镀面很小时也可以不用限热槽,但是电镀面很大时就需要小心,因为此时不容易焊接。
You can omit the thermal reliefs when the plane is quite small, but be careful because the pin may be hardly solderable if the plane is too large.
应用推荐