本文提出异步时序电路的设计方法。
A method of designing asynchronous sequential circuits is presented.
主要讨论功率电路的设计方法。
The design methods of the power circuits are mainly discussed.
提出了一种红外焦平面器件驱动电路的设计方法。
A new design of driving pulse circuit for Infrared Focal Plane Arrays (IRFPA) with CPLD is presented in this paper.
提出了一种新型的CMOS电流转换电路的设计方法。
This paper presents the design method of a novel CMOS current conversion.
介绍了一种基于FPGA的平板显示器件驱动电路的设计方法。
A design method of a driving circuit for flat panel display based on FPGA is introduced.
本文主要介绍煤电钻综合装置电源与漏电保护电路的设计方法。
The paper mainly introduces the design method of power supply and earth-leakage circuit for the electric-coal-drill integrated unit.
讨论了系统的硬件电路的设计方法和点到多点的无线通信协议。
The design method of systemic hardware circuit and the wireless communication protocol is discussed. This introduced wireless measurement and control system.
重点介绍了其主电路以及IGBT的驱动保护电路的设计方法。
This paper focuses on the main circuit, the design method of the drive and protective circuit of IGBT.
因此，我采用集成电路的设计方法来避免一些模拟电路的一些缺点。
So, I adopt the integrated circuit design method to avoid some shortcomings of some simulation circuit.
第四章主要阐述了应变仪信号测量电路及电桥电源电路的设计方法。
Fourth chapter mainly elaboratess the signal conditioning circuit of strain gauge and the supply circuit of strain bridge system's design methods.
给出了一种基于FPGA的等占空比任意整数分频电路的设计方法。
This paper gives out a design of the equal duty ratio arbitrary integer frequency divider based on FPGA.
本文所涉及的是可控硅的整流电路、控制电路及反馈电路的设计方法。
This article concerns about the design for commutating circuit, controlling circuit, and feedback circuit of controllable silicon.
论述微波倍频器的基本设计原理及一种S波段三倍频电路的设计方法。
This paper discusses the fundamental principle on designing microwave frequency multiplier, and the method of designing a kind of S-band microwave frequency multiplier.
阐述了该传感器的检测原理，同时介绍了探头和振荡电路的设计方法。
The measuring principal is given. Simultaneously, the detector of sensor and oscillator circuit is developed.
介绍一种在机车故障诊断系统中使用的司机室显示屏控制电路的设计方法。
A new type of liquid display screens in the cabs for the fault diagnosis systems on locomotives is presented in this paper.
本文简单介绍了SAPF的工作原理、系统结构，详细阐述了主电路的设计方法。
This thesis simply introduces the operation principle and system configuration of SAPF, and describes the design method of main circuit in detail.
阐述了地铁车辆设置列车母线电路的重要意义，提出了列车母线电路的设计方法。
It is described the great sense to have a train bus circuit for metro vehicles, and a design method is proposed.
介绍LTC2900的特性与原理，分析关键电路的设计方法，给出两种应用电路。
The characteristics and principle of LTC2900 are introduced, the designing method of the key circuit is analyzed and two application circuits are also given.
与以往十值电路的设计方法相比较，此设计方案具有编码效率高、供电电压低等特点。
Compared with the conventional design of ten-valued circuits, the design has the characteristics of high coding efficiency, low voltage supply, etc.
本文叙述了CMOS集成电路的辐射损伤机理，并给出抗辐射加固集成电路的设计方法。
This paper describes the mechanism of radiation for CMOS IC, and gives out the method of design for radiation hardened IC.
本文从系统的角度出发，分析了信号处理电路的基本原理，讨论了各单元电路的设计方法。
From the viewpoint of system, the paper analyzes the principle of the signal processing method, and discusses the design consideration of each block of the circuit system.
研究了应用线性光耦合器组成模拟信号隔离电路的设计方法、调试方法以及提高线性度的方法。
The design method, debug method and the method of enhancing degree of linearity are researched in the constituting of analog signal isolating circuit with linear optical couplers.
本文叙述了慢扫描电路的设计方法，提出了一种新型偏转线圈结构，它能获得均匀的偏转磁场。
A method of designing slowly-scanning circuits is described and a new type of deflection coil that can offer a uniform deflecting magnetic field is proposed.
介绍了LED大屏幕扫描电路的设计方法，阐述了可编程逻辑器件在高速数字系统应用中的优点。
The design method of LED big screen scanning circuit is introduced, and the virtues of programmable logic device application on high-speed digital system are presented.
介绍了具有优异性能的数字比例无线遥控电路的设计方法，详细分析了典型应用电路的工作原理。
The design method of the digital proportional wireless remote controller circuit with the excellent performance is presented in this paper.
文中还介绍了IGBT栅极驱动电路和IGBT电压均衡电路的设计方法，并给出调制器的输出波形。
The design of the grid-driven circuit and the voltage balancing circuit for IGBT are also introduced, giving the output wave of the modulator.
导出了DT触发器的激励表，提出了应用DT触发器的时序逻辑电路的设计方法，并给出了设计实例。
In this paper, DT flip - flop excitation table is developed, the design method of sequential logic circuits using DT flip - flop is presented, and the design example using the method is given.
通过对一台3 1 5A全桥式IGBT逆变手弧焊电源主电路的设计，介绍了逆变电源主电路的设计方法。
This paper presents a design method of the main circuit of IGBT inverter for SMAW by an example of designing the main circuit of IGBT inverter based on full bridge for SMAW (315A).
根据组合逻辑电路的设计方法，突出用卡诺图化简逻辑表达式在并联比较型A/D转换器编码电路设计中的应用。
To stress the application of Karaugh map on designing of coding circuits in parallel-comparator ADC in terms of the design of combinational logic circuits.
文中着重地介绍了BMS子系统中电池均衡系统及其保护电路的设计方法，同时介绍了电压采集及温度控制等电路。
This article focuses on cell equalization and its protection circuits in the subsystem of BMS, and also circuits of voltage and temperature is recommended.
应用推荐