概述了控制系统的电源电路、驱动电路、显示电路与软件设计及信号采集的方法。
The power supply circuit, driving circuit, display circuit, software design and signal collection of the control system are outlined.
该管材8604支持软件控制的串器的产出，使优化电源和信号强度的系统。
The PEX 8604 supports software control of the SerDes outputs to allow optimization of power and signal strength in a system.
该控制方式的指令信号通过同时检测电源电流和负载电压得到。
The reference signal in this control approach is obtained by detecting both source current and load voltage.
单相电力电子控制器从斯潘851数字晶闸管电源提供软件的最新数字信号处理（DSP）技术和。
The Single-Phase 851 Digital SCR Power Controller from Spang Power Electronics offers the latest in Digital Signal Processing (DSP) technology and software.
在设计中，以TL 494作为PWM产生电路输出控制信号，控制开关管的导通状况，在半桥反激式输出的基础上实现了电源的多路输出。
In the design, to produce circuit TL494 as a PWM output control signals, control of the on-switch situation, the half-bridge flyback output on the basis of the power of multi-output.
接口信号电源控制器与计算机的853数码允许控制器真正应用定制任何工业加热。
Interfacing the 853 digital signal power controller with a computer allows the controller to be truly customized for any industrial heating application.
讨论了一些影响放电电压大小及频率的电源参数，如供电电压、控制信号占空比、振荡电路的电阻和电容等。
Some factors affecting the frequency and magnitude of power supply, such as supply voltage, duty of control signal, the resistance and capacitance of oscillation circuit are discussed.
此电路采用基于DSP控制系统的两路开出信号来实现开关电源的软启动。
Two starting out signals of the DSP control system is used to realize switching power supply's soft start.
它以SA 4828作为SPWM信号发生器，经过驱动电路控制IPM模块，产生三相变频电源。
The SA4828 used as SPWM signal generator controls the IPM via driver circuits to produce variable frequency power supply.
其硬件部分主要由六个模块组成：信号调理模块、时间校对模块、存储器模块、网络控制模块、WDT模块和电源管理模块。
The hardware mainly comprises six modules: signal procession module, time adjusting module, memorizer module, network control module, WDT module and power management module.
用数字信号处理器(dsp)和复杂可编程逻辑器件(CPLD)设计了IGBT感应加热电源控制系统。
The control system of IGBT induction heating power supply is designed based on DSP (digital signal processor) and CPLD (complex programmable logic device).
由于同步信号受电网谐波的干扰，常使微机控制的中频感应加热电源不能正常运行。
A medium frequency induction heating power source controlled by the microprocessor can not be run normally, in case its synchronous signals are disturbed by the harmonic from common network.
一粒被连接到一个或多个时钟域并连接到至少一个电源域，并且包括定义的信号和用于功率控制的情况。
A grain is connected to one or more clock domains and attached to at least one power domain, and includes defined signals and conditions for power control.
控制系统以16位数字信号处理器TMS320F 240为核心，对整个电源进行了实时的闭环控制。
To realize real time closed loop control, high performance 16-bit DSP TMS320F240 is adopted as control kernel.
它除了给机车上的蓄电池充电之外，还给机车提供稳定的110V辅助电源，为控制系统以及信号发生电路供电。
Besides the storage battery charging, it works as a stable 110v auxiliary power supply which provides electric energy to the control system and signal produced circuit.
对影响放电电压大小及频率的电源参数进行了讨论，如供电电压、控制信号占空比、振荡电路的R和C等。
Some parameters affecting the frequency and magnitude of power supply, such as supply voltage, duty of control sigal. the R and C of oscillation circuit are discussed.
模拟部分主要包括电源、功率控制、信号产生、信号调制、高压输出控制和反馈控制电路。
The analog part mainly includes power source, power control, signal generation, signal modulation, high voltage output control and feedback control circuit.
数字信号处理器(dsp)已经广泛应用于电机控制、开关电源等领域。
Digital signal processors (DSP) have been extensively used in areas of motor control and power switch supply control system.
在载车板控制单元中，分别介绍了主从机通信、输入信号检测、状态显示、手动功能以及电源的设计方法。
As to the loading board part, many design methods are introduced, such as master-slave communication, input signal detection, status displaying, manual action, power supply and so on.
开关电路响应控制信号确定是否向芯片施加电源电压。
The switching circuit determines whether to apply the power supply voltage to a chip in response to the control signal.
铁路信号电源系统是专门给列车运营信号供电的，其可靠性要求非常高，因此，对铁路信号电源的监视和控制十分重要。
Railroad signal power system is a special supply power source for train running. The high reliability is required. Thus, its supervisor and control become very important.
数据采集卡采集程控电源的输出以实现对程控电源的闭环控制，采集发电机控制器和汇流条功率控制器的保护信号以计算延时时间。
Data acquisition card collects data about the power output to realize a close-loop control, and protection signal of the two controllers to compute the delay time.
系统控制方面，通过单片机系统产生四路信号，经驱动电源直流放大后加载到压电陶瓷微位移器上。
As to controlling system, the four-channel signals from MCU are output to DC amplifier to be amplified and then loaded to PZT platform.
本文针对回流焊机温度控制系统自身的特点，分析了造成系统不能可靠工作的各种原因，设计了较高性能的电源线滤波器和信号线滤波器。
All kinds of causes of the reflow control system which can not work normally is analyzed, and new power filter and signal filter are designed.
介绍了基于数字信号处理器（DSP）控制的焊接电源结构。
This paper introduces the frame of a welding power source based on Digital Signal Processor(DSP).
本文以DSP（数字信号处理器）为控制核心研制了一套CO2焊接数字化弧焊电源。
In this paper, a digital welding power source based on DSP(digital signal processor) has been developed, which is designed for CO2 welding.
为了控制TH7195，计算机一定要发送指令，而且电源最后将会送一个应答信号。
To control the TH7195, the computer must send instructions, and the power supply will eventually send an answer.
为了控制TH7195，计算机一定要发送指令，而且电源最后将会送一个应答信号。
To control the TH7195, the computer must send instructions, and the power supply will eventually send an answer.
应用推荐