第三焊线电性连接于第二芯片与承载器之间。
The third bonding wire is electrically connected between the second chip and the loader.
第二焊线电性连接于中继线路基板与承载器之间。
The second bonding wire is electrically connected between the relay circuit base board and the loader.
第一焊线电性连接第一芯片与中继线路基板之间。
The first bonding wire is electrically connected between the first chip and the relay circuit base board.
银钎焊法:将焊线或焊杆点在阀门里的管道套座上。
Silver brazing Method: Apply brazing wire or rod at point where tube enters valve socket.
上表中的料号,我们有不同的电压,频率,脚距,音压,焊线…可供选择。
The specs in above table, we have different version for different voltage, frequency, pin pitch, wires, SPL... etc.
主要设备有开卷落料线、主焊线、数控龙门铣等生产主辅设备351台(套)。
The main equipment including Open blanking Production Line, Main welding Production Line, CNC Gantry Milling, other Production or auxiliary equipment, a total of 351 sets.
采用双螺旋焊线提高了连接强度,减少了重叠率使之小于50%,从而达到成本低。
The double spiral wire solders are adopted to improve the connecting strength and reduce the overlapping coefficient to less than 50 percent, thereby reducing the cost.
MOSFET的封装主要由晶圆切割,晶粒黏贴,焊线,封塑,切割成型这五大流程组成。
The assembly of MOSFET is consisted of five main processes, which are wafer sawing, die attach, wire bond, molding, trim and form.
侧围总成装焊线是上汽通用五菱汽车股份有限公司自行设计、制造的集机、电、液为一体的自动化程度较高的装焊线。
Assembling and welding line for lateral assembly is a self-designed and manufactured assembling and welding line with full automation, which integrate mechanical, electronic and hydraulic technology.
所述压力机构(36)通过供给单元(39)填充有气态或液态介质,以调节由输送机构(28)施加在焊线(13)上的接触压力。
The pressing means (36) is filled with a gaseous or liquid medium via the supply unit (39) in order to adjust the contact pressure applied to the welding rod (13) by the conveying means (28).
同时研究了芯片与微带线间距的互连、微带线制作、材料的可焊性及焊接过程等制造技术。
And other manufacturing technologies-interconnect between the chip and microstrip, manufacture of microstrip, solderability of available materials and soldering process are discussed.
为了用较小的规模模拟相对较长的金线和较大的焊盘,提出了一种温度场分析的等效方法。
To simulate the long gold wire and large bond pad, an equivalent method was presented in thermal analysis.
它是现代高频直缝焊管生产线和冷弯型钢生产线的主要设备之一。
It's one of the main machines in the modern pipe mill line and formed section line.
但多数情况下,只能采用焊接的方法,将芯线焊在孔形插针的尾部。
However, in most cases, only the use of welding method, cored wire solder in the pin-hole-shaped tail.
不带软铜编织线的磁保持继电器,负载引出脚不能锡焊,不能随意扳动,且不能同时刚性固定两个引出脚。
Not with braided line relay, the load pin can not solder, not arbitrarily wrenched, two pins and rigid fixation.
本文介绍超声波在国产轿车后保险杠总成焊接中的应用,着重介绍了该焊装线的组成。
The paper describes the application of the ultrasonic in welding car's bumper, especially in the construction of the welding line.
用三维有限元方法对超声波线焊进行了瞬态的热-结构分析。
Thermal-structural analysis was performed for ultrasonic wire bonding(UWB) by three dimensional finite element method(FEM).
在订购对焊连接阀门时,要指定管道连接端口的管壁厚度,并且提供有关类型、型号和焊接端等高线等参数。
When ordering Butt Welding End valves, specify schedule of pipe end and give complete data concerning style, figure number and contour of weld end.
介绍了螺旋焊管成型器内压辊斜置小辊线接触辊型的设计方法(经验公式设计法)。
The article introduces the design methods of contact roller of internal press roller of forming machine of SSAW pipe mill(experience formula design).
针对焊管生产线工程中一些由土建设计、施工带来的直接影响设备安装精度、周期等问题,提出了相应的控制措施。
It raises the relevant control measures aimed to effect units installation accuracy, cycle problem, etc. caused by civil design and construction during welded pipe production line project.
AIM生产各种焊材产品所需的原材料,包括:锡粉、介质、锡线松香芯和助焊剂。
AIM produces all the needed raw materials for it's solder products including powder, mediums and core wire flux.
采取严格清理焊接区、高焊材纯净度、强熔池保护及控制线能量等措施消除了蒙乃尔合金焊接中的气孔和热裂纹,保证了产品焊接质量。
By strictly clearing up weld zone, improving welding material's purity, strengthening molten pool's shield and controlling energy input etc measures, weld zone's hot crack and blowhole were prevented.
焊管机组在线矫平机是焊管生产线的主要设备之一,为了确保高强度、大直径、厚壁焊管生产的顺利进行,矫平机的性能十分重要。
Online Flattener is main equipment of welded pipe unit, the property of Flattener is very important to ensure production of welded pipe with larger wall thickness going well.
焊装主线是汽车焊装生产线的核心部分。
Main line is the heart part of car body welding production line.
本文介绍了—种汽车焊装生产线CAD系统。
CAD system for car body welding producing line is presented.
结合已设计出的45~76焊管生产线中的六辊矫直机,阐明了矫直辊辊型设计的一种方法。
The paper, combined with the 45~76 straightening machine designed, provides a theoretical method for designing the straightening roll camber.
本文参照有关标准确定了引进焊管生产线液压缸测试台的测试项目;
Measurement items for hydraulic cylinders used in imported welded pipe production line were determined according to related standards.
结合实践,探讨了汽车焊装线气动系统的基本设计技术。
And basic design technique of pneumatic system of Automotive welding line is discussed combined with the practice.
结合实践,探讨了汽车焊装线气动系统的基本设计技术。
And basic design technique of pneumatic system of Automotive welding line is discussed combined with the practice.
应用推荐