本文利用空间环境效应地面模拟设备对环氧结构胶粘剂进行了真空热循环试验。
In this paper, using ground-based simulation facilities, the vacuum thermal cycling test was carried out on the epoxy construction adhesive.
本文利用空间环境效应地面模拟设备对环氧结构胶粘剂进行了真空热循环试验。
Study on preparation and properties of heat-resistant epoxy adhesive cured at room temperature;
论述了各种类型热试验（热平衡试验、热真空试验、热循环试验） 在航天器研制中的重要性及它们的做法要点。
The paper discusses the importance and implementation of various types of thermal tests (thermal balance test, thermal vacuum test and thermal cycling test) during the spacecraft development phase.
真空热循环试验前后CF/EP层合材料的拉伸性能由电子万能材料试验机完成，本文利用扫描电镜观测试样表面形貌和拉伸后的断口形貌。
The tensile strength and Young's modulus of CF/EP specimens before and after vacuum thermo-cycling were measured by an electrical universal material testing machine.
采用真空热循环试验装置，模拟近地轨道空间环境，研究了LF 6铝合金焊接接头拉伸性能和微观组织，分析讨论了真空热循环对焊接接头的影响规律。
The tensile properties and microstructure of LF6 aluminum alloy weld joint under simulating near earth space environment are studied by means of vacuum thermal cycling system.
通过钨极氩弧焊试验，对焊接热影响区温度场进行分析和研究，建立了焊接热循环曲线。
The temperature field in welding HAZ was studied and analyzed. Welding heat curve was set up by argon-shielded tungsten arc welding experiment.
采用焊接热模拟试验方法研究了在焊接热循环和应力-应变循环同时作用下，2090铝锂合金焊接热影响区显微组织和力学性能的变化特征。
The variation of microstructure and mechanical properties of the welding heat-affected zone of 2090 Al-Li alloy were investigated by means of the welding thermal, simulated and strain cycles test.
利用该模型，根据少量试验数据可预示长期冷热循环下的永久变形或工作寿命。
Using this model the permanent distortion and work life in long term under thermal cycling can be predicted based on a few test data.
试验包括热循环、应力循环和应力热循环等。
Experiments carried out include thermal, stress and stress-thermal cyclings.
从实用出发对316不锈钢管材进行了热循环下的裂纹扩展试验。
The thermal fatigue test was performed on 316 SS to understand the crack propagation behavior underthe cycling temperature environment.
试验研究了太阳电池结构的热循环效应。
The thermal cycling effect on silicon solar cell structure was studied in the paper.
采用焊接热模拟试验和冲击试验，研究了X80管线钢焊接热循环对粗晶区组织性能的影响。
The influence of welding thermal cycle on structure and properties in grain-coarsening region of X80 pipeline steel was investigated by weld thermal simulation technique and the charpy test.
目的研制冷热循环机械载荷咀嚼模拟疲劳试验机来人工模拟口腔环境的温度变化和咀嚼负荷，检测口腔材料的疲劳寿命。
Objective to design a new kind of thermocycling and mechanical loading (TCML) chewing simulator and test the chronic fatigue characteristics of dental materials and prosthesis.
试验结果表明，随真空热循环次数的增加，质损率增大，并经约48次真空热循环后趋于平缓；
The results show that the mass loss rate increases with increasing the vacuum thermal cycles, and becomes flat after 48 cycles;
试验结果表明，随真空热循环次数的增加，质损率增大，并经约48次真空热循环后趋于平缓；
The results show that the mass loss rate increases with increasing the vacuum thermal cycles, and becomes flat after 48 cycles;
应用推荐