如果我正确地读中文的话，这大约是讨论轨滑动磨损。
If I am reading Chinese correctly, this is about slide wearing down the rails.
结果表明：低压等离子喷涂涂层的滑动磨损量小于空气等离子喷涂涂层。
The results indicate that the wear loss of WC - co coating plasma-sprayed at low-pressure is less than that in air.
通过落球冲击和滑动磨损试验探讨了冲击对高铬铸铁和奥氏体不锈钢耐磨性的影响。
Effect of impact on wear resistance of high chromium cast iron and austenitic stainless steel has been studied by ball-on-ball impact and pin-on-disc abrasion test.
为提高基于磨粒的机器状态监测的准确性，研究了磨粒特征随滑动磨损进程的变化规律。
The evolutions of wear debris characteristics as wear progress in sliding wear process was studied.
高钒高速钢干滑动磨损机理为显微切削和疲劳磨损的复合，并且有应力作用下碳化物的碎裂及脱落。
The wear mechanism of high vanadium high-speed steel is combined micro-cutting and fatigue wear with carbide particle breaking and peeling off under stress.
利用金相显微镜、X射线衍射仪、电子探针及滑动磨损试验机，研究了合金熔覆层的显微组织及性能。
The microstructure and properties of the composite coatings were investigated by optical microscopy, X-ray diffractometer, electron probe microanalyzer and a skimming wear machine.
滑动磨损试验是在“柱-盘”试验机上进行的，其固定的圆柱为52100钢，在旋转的圆盘试样上滑动。
The sliding wear tests were conducted on the "cylinder-on-disc" machine with the stationary cylinder of steel 52100 sliding against the rotating disc specimens.
所有产品需经历撞击试验、渗漏水试验和滑动磨损试验等测试，其安全性、防水性和流畅性在同行业中领先。
All products need to experience the impact test, leakage test and sliding wear test and other tests, the safety, waterproofing and fluency are in the same industry-leading.
本文综述了近年来国内外学者在高分子材料磨损方面的研究工作，着重阐述了滑动磨损、磨粒磨损、冲蚀磨损的研究进展。
In this paper, the research works on the wear of polymers are reviewed, mainly in the aspects of sliding wear, abrasive wear and erosive wear.
其主要功能是减少轴瓦与曲轴间的滑动摩擦磨损，提高发动机曲轴及连杆的使用寿命。
Its primary functions are to reduce wear and tear between bearing and shaft, and raise longevity of shaft and connection rod.
突破为汽车行业：低磨损冰核滚针轴承滑动轴承取代的传播中的传奇大众甲壳虫。
A breakthrough for the automotive industry: Low-wear INA needle roller bearings replace plain bearings in the transmission of the legendary VW Beetle.
影响金属材料磨损的因素很多，如载荷、滑动速度、环境介质、温度、材料的性质等。
There are many factors which affect the wear of metals, such as load, slide velocity, environmental medium and temperature, metal properties and so on.
不使用时，必需做好车床的清洁保养工作，防止切屑、砂粒或杂质进入车床导轨滑动面，把导轨“咬坏”或加剧它的磨损。
When not in use, it is necessary to do the maintenance work of the lathe, prevent scraps, sand or impurity into lathe guide sliding surface, put rail "chewed" or worse it of wear and tear.
汽车转向梯形机构的设计在汽车设计中占据重要的地位，合理的设计可以减小车轮在转向过程当中的滑动，使轮胎的异常磨损控制在允许的范围内。
The design of Ackerman geometry plays a very important role on vehicle design, reasonable design could reduce the slipping in turning, make the abnormal wear in a permissive range.
用双隐层BP人工神经网络，建立了丝杆螺母副的磨损率与滑动速度关系的数学模型。
By the use of double hidden layered BP artificial neural network a mathematical model of relationship between wear rate of screw-nut pair and sliding speed is established.
EMP磨损率随滑动速度和载荷的升高耐增加，但不同试验条件的增幅不同；
The wear rate of EMP increased with increasing of velocity and load at different rates under various test conditions.
阻尼器经过几年的运行以后，阻尼器内部的液压介质、密封件也会发生不同程度的老化，相对滑动的零件之间也会产生不同程度的磨损；
After several years' operation, hydraulic medium and sealing elements inside the damper also have different degrees of aging, and abrasion is also caused among relative sliding parts;
在连续载荷下，因为磨损和压紧，该滑动面是光滑的，将导致粘结应力的进一步下降，类似于无节钢筋的情况。
Under continued loading the sliding surface is smoothed due to wear and compaction, which will result in a further decrease of the bond stress, similar to the case of plain bars.
按照这种方式，可以在依赖于所确定的参数情况下，一方面将离合器增加的磨损最小化而另一方面将直至达到离合器的滑动区域所需的换挡时间最小化。
This makes it possible to minimize, as a function of the specific parameters, both increased wear of the clutch and a required switching time until a slip region of the clutch is reached.
分析了有机硅室温胶装置中搅拌釜底部滑动轴承在使用中易于磨损，更换频繁的原因。
Writer analysizes the problems of easy wearing and exchanging frequently the sliding bearing which was used in a stirring reactor for RTV silicone rubber unit.
研究结果表明：半固态挤压成形合金具有细小、均匀的微观组织和良好的耐磨性，磨损失效形式以滑动和磨粒磨损为主。
The results show that the alloy possesses fine and uniform microstructure and excellent wear resistance in which slide and abrasive wear are dominant in the wear behavior.
磨损失效系指表面之间的相对滑动摩擦导致其工作表面金属不断磨损而产生的失效。
Wear failure refers to the relative sliding friction between the surfaces causes the surface of the metal continue to wear their work arising from the failure.
本发明提供一种滑动结构，其能够切实地抑制由非晶质碳被膜和有机钼化合物的化学反应所导致的非晶质碳被膜的磨损。
Disclosed is a slide structure which can ensure to suppress the abrasion of an amorphous carbon film caused by a chemical reaction between the amorphous carbon film and an organic molybdenum compound.
根据对碳素钢进行的干燥滑动摩擦磨损试验结果，对碳素钢的磨损量、磨损形态与载荷的关系加以分析。
According to the friction and wear experimental results of dry slide of carbon steel, this paper analyses the relationships between the wearing amount, types of carbon steel and load.
一些使用滑动轴瓦的设备在重载情况下，滑动轴瓦磨损严重，影响生产任务的正常进行。
Some sliding bearings of the heavy loading equipment will be wore seriously, and affect the normal progress of the production assignment.
如果密炼机的轴滑动面磨损，可用金属喷镀方法修补，然后再磨光至原直径尺寸。
If the axis sliding surface wears, available metal spraying method patching, then regrinds the light to the original diameter size.
密炼机的主要是轴子轴与轴承衬的滑动摩擦表面磨损，变得粗糙，造成轴承漏油。
Is mainly the axle axis and the bearing bush sliding friction surface wears, becomes rough, creates the bearing oil leak.
磨损量与滑动摩擦功呈线性关系，与滑动距离成正比。
Mass loss is linear with sliding friction works and in proportion to sliding distances.
在干滑动摩擦过程中，磨损机制主要为氧化磨损和粘着磨损。
The wear mechanisms during dry sliding process are oxidation wear and adhesive wear.
在干滑动摩擦过程中，磨损机制主要为氧化磨损和粘着磨损。
The wear mechanisms during dry sliding process are oxidation wear and adhesive wear.
应用推荐