结果表明：浸润面为一椭圆抛物面，所得结论与实验结果相符。
The result shows that the infiltrated surface is an elliptic-parabolic one, and the conclusion accords with the results of experiment.
浸润面影响规律及其与浸出率之间关系的研究是一项新的研究课题。
The influence rule of the saturated surface and the relation of the saturated surface and leaching rate are new research tasks.
为此，在考虑浸润面影响的基础上建立了大小潮水位波动的数学模型。
Thus, with the effects of seepage face taken into account, a numerical model for spring-neap tidal water table fluctuations is developed.
因此确定浸润面位置的方法正确与否，对稳定性分析的结果是否准确至关重要。
Therefore whether the approach to locate the phreatic surface is appropriate or not is essential to the accuracy of the stability analysis.
在堆浸生产过程中，浸润面受多种不确定性因素的影响，因此浸润面的演化规律很难被准确描述。
During the heap leaching process, the saturated surface is affected by many kinds of uncertain factors, so it is very hard to describe the evolvement rule truly.
为了获取三维数值化概念机模型的浸润面积和横截面积等几何特性，本文提出了一种基于离散化面元的估算方法。
To estimate the geometric characteristics, especially wet areas and section areas, of three dimensional numerical conceptual aircraft models, a method based on surface elements is proposed.
本文采用自行设计的试验装置进行了室内模拟试验，探明了相关因素对浸润面高度的影响规律及浸润面高度与浸出率之间的关系。
In this dissertation, the influence rule of the saturated surface and the relation of the saturated surface and leaching rate are proved up by simulating heap leaching in the lab.
本文采用混沌局域预测法建立了一个线性模型对浸润面实测数据进行预测，预测结果表明，建立的混沌预测模型计算量较小，易于操作且预测精度较高。
The results show that the calculating quantity of the proposed forecasting model is less and the model is prone to be operated and the precision of forecasting is better.
本文从浸润剂原材料的选择、拉丝工艺和烘干工艺三方面分析了浸润剂迁移现象产生的原因及其对短切毡的影响。
In this paper, the causes of size migration and its effects on chopped strand MATS are analyzed from aspects of raw material selection, fiber drawing process and fiber drying process.
提出了自由面适应网格方法，该方法与传统方法相反，即在迭代求解过程中不改变网格而是让浸润线不断地去适应网格，采用网格映射的方法去确定浸润线，直至最后达到允许精度，得到要求的浸润线分布。
Most of the traditional methods used to determinate the free surface profile are based on modifying or changing the grid system to adapt the changing water surface during the iteration process.
被燃油浸润过，没有可匹配的装配面且与下部零件没有相通的过滤油路的零部件需进行二级剩磁检测。
Parts which are fuel wetted, do not have match-fit surface, and do not provide an unfiltered fuel path to downstream parts, should be defined as parts requiring Level 2 residual magnetism.
另一方面，也可以巨大、形状不规则，切面示浅粉到褐色、质硬、有沙砾感、局部纤维化和浸润性边界。
On the other hand, it can be large and irregularly shaped with light pink-tan, firm, gritty, focally fibrotic cut surfaces with infiltrative borders.
另一方面，也可以巨大、形状不规则，切面示浅粉到褐色、质硬、有沙砾感、局部纤维化和浸润性边界。
On the other hand, it can be large and irregularly shaped with light pink-tan, firm, gritty, focally fibrotic cut surfaces with infiltrative borders.
应用推荐