半导体设备，机器人，XY工作台，测量和检测设备。
Semiconductor equipment, robots, XY table, measuring and inspecting equipment.
使用测量和检测设备，检查飞机组件，确保符合工程规范。
Inspect aircraft assemblies, using measuring and testing equipment, for adherence to engineering specifications.
这是一项很老的检测方法，但是由一些可用的商品化设备组成，通过测量全血从而检测血栓形成和血栓溶解。
This is quite an old test but there are several commercial devices available and is used on whole blood where it can measure clot formation and clot dissolution.
磨损微粒是机械设备磨损的重要信息载体，基于电感测量原理和磨损颗粒的检测要求，提出了电感式传感器的设计。
Wear particle is an important information carrier, on the basis of inductive principle and monitoring requirement of wear particle, the design of inductive transducer is presented.
通过正确选择（或改进）测试设备和使用高精度刻标机或精确测量原始标距等手段，即可实现冷轧扭钢筋的正确检测。
By selecting test equipment and using high precision scaling device or precisely measuring the primary scale, an accurate testing of cold-rolled and twisted steel bar may be realized.
介绍了SF 6全封闭组合电器设备的气体压力检测、湿度测量、气体管理的方法和注意事项。
This paper introduces the methods and matters needing attention of gas pressure detection, moisture measurement and gas management of SF6 totally en closed combinative electrical equipment.
方法是根据有关卫生标准及检测方法对生产设备、休息室、控制室等作业场所进行声强和频谱的测量。
Methods the sound level and frequency were measured according to the corresponding health criterion and measuring method at big production equipment, crush room, control room and workshop.
作为汽车检测的基本设备—四轮定位仪，是汽车检测维修行业的核心设备，用于测量和校准汽车的车轮定位参数。
Four-wheel alignment, as a basic equipment of vehicle inspection and test is also the core equipment to measure and calibrate the parameter of wheel alignment.
分别研究了电气设备的电流、电压和功率传导干扰的检测技术，阐述了其测量方法和经验。
The paper respectively studies detection technique of the current, voltage and power conduction interference in the electrical installations, discuss is the measure methods and its experience.
以汽车发动机连杆破口缺陷检测为例，讨论了所研制的检测设备的系统设计、参照物标定法和测量流程。
The system design, the method of calibration with reference film and the detection processing according to the detection project of engine rod's surface disfigurement are discussed.
目前，在工业生产和设备检测中，对于金属板材或者金属设备的厚度测量，通常有超声、射线、电磁涡流等不同方法。
Now, in the industry manufacture and equipment testing, there are several methods for the metal thickness measurement, as ultrasonic, X-ray, eddy current and so on.
机械设备检测是对机械零件中包括长度、角度、粗糙度、几何形状和相互位置等尺寸的测量。
Machinery and equipment testing includes the measurements of length, Angle, roughness, geometry and mutual alignment.
经三种不同的外部条件处理后，使用无损检测设备（FFT）和力学试验机对杉木单板层积材试件静曲强度和弹性模量进行测量。
MOE and MOR of LVL which were made of Douglas-Fir were measured by FFT and loading machine after treated under three different conditions.
设有测量室和试验室各一个，负责各项试验和检具、检规校正管理等，针尖拥有各种先进检测设备对产品进行控制。
We set up a measurement room and a laboratory which in charge of all kinds of testing and management of all the inspection tool and gauge.
产品广泛应用在医疗设备、工业控制、检测和测量设备、广播电视和通讯、核工业和军工等各种具有挑战性的环境和场合。
LEMO's high quality Push-Pull connectors are found in a variety of challenging application environments including medical, industrial control, test and measurement, audio-video and telecommunications.
产品广泛应用在医疗设备、工业控制、检测和测量设备、广播电视和通讯、核工业和军工等各种具有挑战性的环境和场合。
LEMO's high quality Push-Pull connectors are found in a variety of challenging application environments including medical, industrial control, test and measurement, audio-video and telecommunications.
应用推荐