应用三维流动模拟软件HSCAE3D6 0对冰箱定位板注塑模的浇注系统进行优化。
A 3d flowing simulation software HSCAE3D6.0 was applied to optimizing the pouring system of positioned panel injection-mould.
在空调控制柜模拟板上运行的结果表明了该故障诊断系统的方案是可行的。
The result obtained from the air-condition simulator proved that the project of the train air-condition controller fault diagnosis system is feasible.
本文介绍了一种应用于电路板测试系统高性能模拟测试接口的研制。重点阐述它的设计思想、硬件结构以及抗干扰措施。
This thesis introduces the design of high performance analog test interface of BDS circuit board test system. It emphasizes the design theory, hardware architecture and anti-jamming measure.
最小系统板与电模拟系统的原理图都有。
Minimum system board with the electrical schematic diagram of the simulation system has.
首先，针对某型精密伺服转台系统中三块电路板（模拟控制板、单片机板和测角控制板）设计了专门的电路板测试仪。
First, a special instrument to test the analog-control board, single-chip board and angle-measure board in the high precision servo turntable system is designed.
STA5型用户板用于数字程控交换机的用户接口，也可做为各类接入网系统的远端二线模拟接口。
STA5 subscriber line is applied to subscriber line interface of programmed control digital switches, and two wire analogy remote interface of access network.
通过PC机与ARM仿真板的通信对本文实现的系统进行了仿真模拟实验，对可视电话的基本功能和性能进行了测试。
Simulation test is performed by communication between PC and ARM emulator to evaluate the function and performance of the video phone system.
在空调电控板测试诊断系统中采用了软件信号仿真和硬件信号模拟相结合的设计方法，最后采用多线程、多优先级的编程技术进行实现。
This system is designed by employing the method of combining signal emulation with signal simulation in addition to multithreading and multi-priority programming technology.
利用作者已开发的汽车覆盖件成形预测系统，针对一汽车车门内板的成形过程进行了模拟分析，并对其在试模过程中可能出现的破裂问题进行了预测。
A forming process of the inner panel of automobile door was simulated by means of a developed prediction system. The cracking prediction of the panel during its forming process was given.
该软件可用于封装，电路板及系统级CFD模拟，包括自然对流、强制对流和辐射传热。
This software can be used for package -, board - or system-level CFD simulation, including natural and forced convection and radiation heat transfer.
用80C196单片机作为显示处理机构成一块基于AT总线的插卡，用以取代原平视显示器教学模拟器显控计算机和矢量产生器插件板，使系统结构简化、成本降低，并提高系统可靠性。
An 80C196 MCS based on AT Bus replaces the Display Computer and Vector Generator board of the old HUD Teaching Simulator. It reduces system form and costs, also improves system reliability.
应用计算流体力学的方法可以精确地模拟出气流对芯片的冷却情况，对集成电路板气冷系统的设计具有一定指导作用。
We can precisely describe the effect by Computational Fluid Dynamics, which is useful to the air-cooling system design of circuit board.
通过对低温泵的真空度及其抽速与液氦低温板温度的关系进行模拟，验证了真空系统设计的合理性。
By simulating the temperature of the cryopanel and the relation between the pressure and pumping gas speed of the cryopump, it was verified the vacuum system design was rational.
然后，用两种厚度的聚乙烯板和铁板作模拟检测物进行了系统的计算。
Then, calculations about polythene and iron board scattererswith two kinds of thickness were carried out. Having analysing the calculation results.
首先识别出黏贴压电作动器的柔性板振动控制系统的实验模型，接着提出了利用改变压电片对连接数量来模拟作动器驱动故障的方法。
Firstly, a state space experimental model of flexible plate vibration system with some malfunction connection piezoelectric actuator pairs were identified by the multivariable identification theory.
首先识别出黏贴压电作动器的柔性板振动控制系统的实验模型，接着提出了利用改变压电片对连接数量来模拟作动器驱动故障的方法。
Firstly, a state space experimental model of flexible plate vibration system with some malfunction connection piezoelectric actuator pairs were identified by the multivariable identification theory.
应用推荐