基本模拟电路模块设计。
由于电源电压的持续缩减，以及随着工艺尺寸的成比例缩减，器件的特性也发生了变化，模拟电路模块设计指标也在有着变化。
Design of analog circuit blocks is a moving target because of the continuing scaling of power supply voltage, and because of the changing behavior of devices with scaling of technology.
本次课题研究能够用于白光LED驱动的电源管理方式，并设计其主要的模拟电路模块，为实现低功耗、低成本的LED驱动器提供技术参考。
The purpose of this task study a new power management way used to drive white LED luminescence, and design the general analog circuits'module.
传感模块由传感器电路、调制电路和模拟信号开关组成。
Sensor module is composed of sensor circuit, modulation circuit and analog signal switch.
无源片上电感是RF IC中需求很高的器件，被广泛地应用在LNA、VCO、滤波器等模拟单元模块中，构成了无线移动通信电路的基础。
On-chip passive inductors, basic elements of wireless mobile communication circuits, are highly required in RFIC and widely used in simulating unit modules such as LNA, VCO and filters.
基于斜率故障模型，提出了一种诊断模拟电路中基于闭环集成运算放大器的模块级软故障的字典法。
Based on the slope fault model, this paper presents a fault dictionary method for soft fault diagnosis of modular analog circuit based on closed-loop operational amplifier (CLOA).
性能评估器和优化模块是模拟集成电路自动综合中两个重要的模块。
Performance evaluation and optimization engine are two important modules in the analog integrated circuit automation synthesis.
利用上述方法实现的一些CMOS单元电路的自动综合模块已经集成到FDAADS——“复旦模拟电路自动化设计系统”中。
Synthesis tools for several cell level CMOS analog circuits implemented with the above approach have been integrated in FDAADS—FuDan Analog Circuit Automated Design System.
带隙基准电压源之所以是模拟电路中重要的模块，是因为它能够提供近似恒定的参考电压，这个电压不随温度，电源电压，工艺的变化而变化。
Bandgap reference voltages are important analog circuit blocks. It can provide a nearly constant reference voltage which is stabilized over process, power supply and temperature variation.
介绍由at89c52、RAM、AD574、电源电路、模拟量输入采集处理等模块组成的数据采集系统。
The data acquisition system was introduced which was composed of AT89C52, RAM, AD574, power circuit, analog quantity input acquisition module, etc.
模拟电路计算的对象的使用电动势值和模块内要测量的温度值的温度，并且该值通过I2C总线输出。
The analog circuit calculates the temperature of an object using the electromotive-force value and a measured-temperature value inside the module and the value is outputted through an I2C bus.
本文对芯片工作原理、系统架构设计、模块划分、前端模拟电路实现、版图设计等进行了详细分析。
In this thesis, we illustratre the theory of the chip, system design, partition of the modules, simulation and realization of analog circuit and layout design.
课题着重对这两个模块的电路结构以及版图结构进行了深入的研究和分析，并采用SPICE工具进行了模拟验证。
The paper has an emphatical discussion on the study and analysis of the circuit structure and layout structure of these two modules, and makes a lot of SPICE simulation and verification.
主要介绍CPCI数字存储示波器模块的模拟通道设计、A/D采样设计、数字控制电路设计、电源设计以及CPCI接口设计。
The hardware design of the module mainly presents analogue channel circuit design, A/D acquisition circuit design, digital control circuit design, power and CPCI interface design.
运算放大器作为模拟电路单元的核心模块，它的重要性日益受到人们的重视。
As the nuclear module of the unit of analogue circuits, people pay more and more attention to it.
单刀双掷模拟开关电路的设计包括四个模块：MOS开关电路、驱动电路、缓冲电路和ESD保护电路。
Four modules are included in the SPDT analog switch, for example, MOS switch circuit, driver circuit, buffer circuit, and ESD protection circuit.
同时，本系统的硬件模块不同于传统的模拟、数字电路。
However, the hardware of the system is different from traditional analog or digital circuit.
第5章详细介绍了为实现对突发式光收发模块的测试而设计的突发信号模拟产生器的基本原理与各部分功能电路的实现。
Chapter 5 particularly introduces basic principle of the circuit of the burst mode signal generator used for the testing of the burst mode optical transmitter and receiver module.
基准源模块广泛的应用于模拟和混合电路中，如A/D、D/A转换器，电压调谐器，电压表，电流表等测试仪器以及偏置电路。
Reference sources are widely used in analog and mix-mode circuits, such as A/D, D/A converters, voltage regulators, measurements, instrumentation circuits, and bias circuits.
整个系统分为模拟波形产生、单片机控制电路、FPGA内部功能模块三大部分。
The whole system is made up of three parts, the part of simulative waveform generation, MCU control circuit, function modules internal FPGA.
硬件上详细给出了系统主要功能模块的工作原理和设计内容，包括模拟信号输入电路、数字信号输入输出电路、看门狗及系统复位电路等。
On the hardware design we provide the operation principle of the main function module and design content in detail, including Analog Inputting, Digital Inputting and Outputting, Watchdog, etc.
模拟电路部分包括：电池电源供电模块、信号采集电路、模拟滤波和放大电路、增益调节电路、地电压抬升电路和A/D输入信号限制电路。
The analog circuit consists of power-supply modular, signal pickup circuit, analog filter amplifier, gain control circuit, power ground lifting circuit and signal limit circuit of A/D channel.
主要负责所有模拟电路版图的整体布局、静电保护设计和模块到顶层的集成设计和流片。
You will be responsible for all levels of analog mask layout from floor planning, ESD pad placement, block level layout up to top level integration tape out.
主要负责所有模拟电路版图的整体布局、静电保护设计和模块到顶层的集成设计和流片。
You will be responsible for all levels of analog mask layout from floor planning, ESD pad placement, block level layout up to top level integration tape out.
应用推荐