波函数的模平方正比于体系处在其位形空间各个点的几率密度。
The square modulus of the wave function is proportional to the probability density of finding the system at each point in the configuration space.
结果表明，影响凝胶注模陶瓷坯片密度的因素主要有：料浆的固含量、单体含量、单体和胶联剂的比值。
The research showed that the solid loading, content of monomer and ratio of monomer and crossing linker were the main effect factors on the density.
从理论上分析了凸模虚拟速度和板料虚拟密度对薄板变形能的影响。
The effect of punch virtual velocity and sheet virtual density on the sheet strain energy was studied in this paper.
方法采用两个不同态的密度算符距离函数方法，从理论上研究两个不同多模奇相干态光场之间的距离。
Methods the distance between two different multimode odd coherent state light fields was analyzed theoretically by the method of distance functions of density operator.
主要采用一种具有复合应力场的挤出口模，通过固态挤出茂金属线性低密度聚乙烯获得双向自增强片材。
Biaxial self-reinforced metallocene linear low density polyethylene sheet was prepared by the die with complex stress field in solid state.
研究了HL -1m装置上锁模不稳定性和密度极限破裂。
Locked mode instability and density limit disruption have been studied in the HL 1m tokamak.
采用密度矩阵方法描述了两模反向耦合。
In this paper the method of density matrix is used to describe two coupled modes.
随固相体积分数的增加，水基凝胶注模法坯体密度逐渐增加，但强度逐渐降低。
With increasing solid loading, density of AGC green body increases gradually, but strength decreases gradually.
在多模光纤中，实现低串扰高密度是一个大的挑战。
Achieving low crosstalk and high core density is one of the key challenges for multicore fibre.
高速讯号线和个人电脑及电脑周边的高密度组装之电子设备的共模杂讯抑制。
Common mode noise suppression of signal lines in high speed and high density digital equipment as personal computers and peripherals.
针对板料成形回弹精度问题的数值模拟，从理论上分析了凸模虚拟速度和板料虚拟密度对薄板变形能的影响。
For the simulation accuracy of springback problem in sheet metal forming, the effect of punch virtual velocity and sheet virtual density on the sheet strain energy was studied in this paper.
结果表明，对于高密度EPS模，采用高温失模工艺具有工艺简单、失模快、成品率高、污染小等优点。
The results indicate that removing pattern at high temperature for high density EPS pattern offers the advantages. of simplifying process , fast removing, high yield and less pollution etc.
多模箱式再生系统中过滤体的尺寸可以不受安装空间的限制，并且可以采用多个微波源馈入功率以提高再生腔中的微波功率密度或改善加热均匀性。
In this system, the size of the filter is not limited by the space of installment and it is possible to heat of the filter by using more than one microwave power supply.
基于密度泛函微扰理论(DFPT)结合模守恒赝势方法进行晶格动力学模拟。
Based on density functional perturbation theory (DFPT) and combined with the norm-conserving pseudopotential method, the lattice dynamic simulation is presented.
目的通过试验测试，设计制作出与标准固体体模等效的qct骨密度测量液体体模。
Objective to develop the Liquid phantom used to measure bone mineral content in QCT and has equivalent effectiveness with solid phantom made of Hydroxyapatite.
研究了负压度、模样密度、浇注温度、金属静压头等工艺因素对消失模铸铁件充型速度的影响规律。
The filling speed of lost foam cast iron casting was measured by use of an integrated set of experimental equipment and a specially designed computer acquisition system.
以带圆孔的长方形为例，模拟比较了不同网格密度和注入口位置对充模时间、流动前沿以及干点形成区域的影响。
Flow front, filling time and dry spot were simulated and analyzed through comparing different mesh density and injection location such as the shape of the rectangle with hole.
应用毛细管流变仪测量了在接近实际挤出工艺条件下低密度聚乙烯熔体的流变性质； 应用流动可视化技术，观测了试样熔体流经突然收缩的轴对称口模时的入口收敛流型。
The entry convergent flow pattern was observed with flow visualization technique when the resin melt flowed through a die featuring abrupt contraction in cross-section of channel and axial symmetry.
铝体模来源：美国LUNAR公司生产的DPX - MD双能X射线骨密度仪所配备的自检模块。
Source of aluminum model: self-check die-block equipped by DPX-MD dual-energy X-ray bone densometer produced by American LUNAR Company.
根据垂直管固液两相流的特征 ，考虑固液两相流密度、浓度、弹模、阻力等特点 ，对粗颗粒水力提升不稳定流进行数值模拟。
On the basis of previous researches, the concentration characteristics of large size particles in vertical pipes by hydraulic lifting were studied through experiments and theoretical analyses.
根据垂直管固液两相流的特征 ，考虑固液两相流密度、浓度、弹模、阻力等特点 ，对粗颗粒水力提升不稳定流进行数值模拟。
On the basis of previous researches, the concentration characteristics of large size particles in vertical pipes by hydraulic lifting were studied through experiments and theoretical analyses.
应用推荐