会使用模具间的机器以及检验设备。
拉拔角、钢丝帘线与拉拔模具间的摩擦力是影响织构形成的主要因素。
The experimental results demonstrate that the main factors affecting texture formation are die Angle and the friction between the wire and die.
存在的主要问题是在冲压过程中钢丝坯料易被拉断,通过减小钢丝和模具间的摩擦力及变形力解决了问题。
Through the reduction of friction force and deformation force between the steel wire and die, the tensile failure problem of steel wire workblank during the stamping process was resolved.
基于NUMISHEET93的U形弯曲标准考题,考虑板材与模具间的接触演变过程,建立了一个有限元模型来预测回弹。
A finite element model based U-bending benchmark of NUMISHEET '93 has been used to predict springback with contact evolution between the sheet and dies.
基于NUMISHEET93的U形弯曲标准考题,考虑板材与模具间的接触演变过程,建立了一个有限元模型来预测回弹。
A finite element model based U-bending benchmark of NUMISHEET "93 has been used to predict springback with contact evolution between the sheet and dies."
基于NUMISHEET93的U形弯曲标准考题,考虑板材与模具间的接触演变过程,建立了一个新的有限元模型来预测回弹。
A new finite element model based on U-bending benchmark of NUMISHEET '93 has been proposed to predict springback with contact evolution between the sheet and dies.
介绍了多工位连续模工位间送进方式的类型、结构、适用范围和送进精度,论述了其选用原则及其与模具设计的关系。
Feeding type, structure, applicable range and feeding accuracy of multi-station progressive die have been introduced with description of relationship between selection principle and die design.
装配关系和模具零件由特征描述,特征间的相互联系则由父子关系结构来描述。
The assembly relationship and parts of the die and mould are described by feature.
铸造车间的模具是在工具间生产的。
通过对不同间隙条件下冲裁件断面质量以及不同间隙条件下模具的磨损情况,分析说明了冲模间隙与模具磨损和产品质量间的关系。
Based on the punching section quality and mould wear in different gap conditions this paper analyses the relation between die gap and mould wear and product quality.
装配关系和模具零件由特征描述,特征间的相互联系则由父子关系结构来描述。
The assembly relationship and parts of the die and mould are described by feature. The dependent relationship of features is described by parent-child operator structure.
模具口是V型的,为了随时减少模具和辊轴间的空气间隙。
The die lips are V-contoured to minimize the air gap between the die and the roll nip whenever necessary.
晶间碳化物是破裂源,因此,锋钢作为模具使用时,晶间碳化物增加裂纹倾向性。
Intergranular carbide source is broken, so the mold when used as a front steel, intergranular carbides increased tendency to crack.
该公鸡图案是2007-2008年期间在景德镇博物馆的一部分,即为老瓷器厂内手工绘画而成,器形用模具而成并用纸贴固定图案的方法。
The "Cockerel design" is manufactured by hand during 2007-2008 at the Old Factory, in the museum part of Jingdezhen area, the plates moulded by hand and the pattern put on with a paper method.
该公鸡图案是2007-2008年期间在景德镇博物馆的一部分,即为老瓷器厂内手工绘画而成,器形用模具而成并用纸贴固定图案的方法。
The "Cockerel design" is manufactured by hand during 2007-2008 at the Old Factory, in the museum part of Jingdezhen area, the plates moulded by hand and the pattern put on with a paper method.
应用推荐