有很多曲线控制点的调整才能得到理想的截面。
There are a lot of curve control points adjustments to be done before getting the desired sections.
有针对性的吸管样品添加一个新的层面注入色彩曲线控制点，达到指定目标的颜色，中性色，或色彩校正。
Targetted Eyedropper Samples add a new dimension to color correction by injecting curve control points to achieve a specified target color, neutral color, or hue.
移动控制点就可以改变曲线的形状。
A handle point may be moved to alter the shape of the curve.
详细介绍了用公路路线上控制点坐标进行公路直线和曲线平面位置定线的数学模型。
This paper introduces the mathematical model for highway route alignment. This model can determine plan position of highway straight and curve by the control points.
使用改装命令使用0,1公差，以减少控制点，由此产生的曲线公差范围内。
Use the refit command using 0, 1 tolerance to reduce the control points on the resulting curves within tolerance.
重建曲线至少有6个控制点。这是必要的，以实现理想的连续性当使用曲线表面从网络或扫描第2轨。
Rebuild the curve with at least 6 control points. This is necessary to achieve the desired continuity when using surface from curve network or sweep 2 rails.
NURBS方法在实际应用中遇到的一个重要问题就是已知曲线曲面上的型值点而求解控制点。
An important problem which is brought about by the method of NURBS in practice is that calculating control points based on the curve or surfaces data points.
在算法中，所有的B3样条曲线的控制点可以通过对多边形的顶点简单计算产生。
The control points of the B3-spline to be constructed are computed simply by the vertices of the given polygon.
文中根据曲线曲面型值点，分别用四种参数化方法构造节点矢量，利用NURBS方法反算控制点。
In this paper, the control points are calculated based on the curve or surface's data points and the knot vector which is calculated with four kinds of parameterization by the method of NURBS.
第二个点和第三个点是确定曲线形状的控制点。
The second and third points are control points that determine the shape of the curve.
每条后续曲线只需要三个点：两个控制点和一个结束点。
Each subsequent curve needs exactly three more points: two more control points and an ending point.
贝赛尔曲线的每一个顶点都有两个控制点，用于控制在该顶点两侧的曲线的弧度。
Bezier curves of each vertex has two control points, used to control both sides of the vertex curvature of the curve.
描述形状的重要特征是物体的轮廓曲线，为了提高识别效率，通常使用控制点表达轮廓。
An important feature of shape description is the contour curves of object. To improve the efficiency of recognition, dominant points are usually used to represent the contour.
本文论述了在路线工程曲线段“交点”附近设立2 ~3个能相互通视的控制点对曲线段进行较高精度放样的新方法。
This paper introduces a method of curve setting out in route construction, in which 2 or 3 control points are placed at the intersected point of the curve.
创建罩采用曲线曲线2意见和改装，以减少他们的控制点。
Create the hood curves using curve from 2 views and refit them to reduce the control points.
小波光顺时，通过丢弃细节曲线，保留近似曲线，既保留了原曲线的总体形状，又减少了控制点，最终达到小波光顺的目的。
The whole form of original curve is retained and control points is reduced with discarding detail curve and retaining approximate curve, so the target of fairness is reached.
其中曲线拟合是一个在给定误差下进行曲线逼近的过程，当曲线拟合完成之后，整个曲面的控制点的数目也就确定了。
Curve fitting is a curve approaching process under definite error and the number of control points throughout surface is ascertained after curve fitting completed.
介绍了利用线路平面控制网的控制点测设道路工程中组合曲线中线桩点位的坐标计算、测设方法。
A method for calculating and measuring the coordinates of centering stakes using line control counts in plane control meshwork is introduced in highway construction in this paper.
为第一条曲线创建起始点、结束点和两个控制点；为第二条曲线创建结束点和两个控制点。
Creates the start, end, and two control points for a first curve and endpoint and two control points for a second curve.
由于全站仪和计算机的普及和推广，尤其是GPS定位仪的开发，直接由导线点或其它控制点测设曲线中心线，既快速便捷又减少了累计误差。
Because popularizing and spreading of computer, especially exploiting of GPS, it is convenient and lessening Errors that surveying curve center point from control point.
我已经做了数学如何计算控制点的三坐标曲线的定义必须通过，但现在我需要创建该曲线。
I've already done the math to figure out how to calculate the control point as defined by the three coordinates the curve must go through, but now I need to create this curve.
三次贝塞尔曲线使用两个控制点，与之不同，二次贝塞尔曲线只使用一个控制点。
Unlike a cubic Bezier curve, which USES two control points, a quadratic cubic Bezier curve USES a single control point.
三次贝塞尔曲线使用两个控制点，与之不同，二次贝塞尔曲线只使用一个控制点。
Unlike a cubic Bezier curve, which USES two control points, a quadratic cubic Bezier curve USES a single control point.
应用推荐