将不锈钢和普通钢焊接在一起是可能的。
研究发现,同普通钢相比,耐火钢获得了良好的高温性能。
It was found that the properties of FR steels were significantly better than the plain steel at high temperature.
由于渗氮钢的合金比例,它们比普通钢更强,也容易热处理。
Nitriding steels, by virtue of their alloying content, are stronger than ordinary steels and respond readily to heat treatment.
根据简单的镜子概念影响普通钢盆艺术家实现这一厨具奇特合奏。
Based on the notion of simple mirror-effects on ordinary steel pots the artist realized ideosyncratic ensembles of this kitchenware .
可更换的自锐塑料拳能够显着持续时间超过普通钢拳打在大多数应用中。
Replaceable self-sharpening plastic punches are able to significantly outlast conventional steel punches in most applications.
采用普通钢球作为对比,研究磨矿过程中以铸铁段为细磨介质的破碎效果。
Comminuting effect in grinding process by using cast iron segment as fine grinding media is studied with comparison to steel ball.
我们的锋利塑料冲是自激化,并能显着持续时间超过普通钢在大多数应用中拳。
Our razor sharp plastic punches are self-sharpening and are able to significantly outlast conventional steel punches in most applications.
探讨了采用分光光度法对普通钢、低合金钢中的硅、磷、锰、铬进行联合测定。
A method for the joint determination of si, p, Mn, Cr in general and low alloy steels is discussed by means of spectrophotometry. The method is simple, rapid and easy to master.
普通钢屋架结构厂房的屋盖根据屋面材料和屋面布置情况,可分为无檩屋盖和有檩屋盖。
According to the material and disposition, the roof of common steel roof truss mill building divides into steel purlin roof and roof without purlin.
主次结构的连接转换节点有着与普通钢节点完全不同的索钢接触单元的特殊构造,受力复杂。
The exchange joint between the major and minor steel structure with complex mechanics is totally different from the normal joint.
用途广泛,使用于铝、铜、铁、锌、不锈钢、普通钢、镍、钨、合金以及异类金属之间的焊接。
Wide-ranged applications, especially in the welding of copper, iron aluminum, steel, stainless steel and alloy.
普通钢在系统中会溶解,铁离子会污染超滤膜,导致在清洗后超滤效果也不好,甚至要更换超滤元件。
Mild steel in this system will dissolve and contaminate the membranes with iron, resulting in reduced efficiency even after cleaning and therefore should not be used.
油回火钢丝是专门锻炼高碳钢丝,以提供更大的强度和耐磨性,但其耐冲击是有点低比普通钢高碳钢。
Oil tempered wire is specially tempered high carbon steel wire to provide greater strength and abrasion resistance, although its resistance to impact is somewhat lower than regular high carbon steel.
新开发研制的碳纤维复合柔性连续抽油杆克服了普通钢杆的缺点,能够满足低渗油田小泵深抽技术的要求。
The new developing carbon fiber compound flexible coiled rod overcome the shortcoming of ordinary steel rod, can meet the need of low permeability oilfield production.
不像含碳的塑料叶片那样易弯曲与摆动,在LAKOTA叶片内的碳纤维硬度是普通钢的7倍,能从顶到底运载。
Unlike plastic with powdered carbon blades that bend and flutter, the carbon fibers in the Lakota blades are 7 times stiffer than common steel, and carry the loads from tip to root.
对比分析了普通钢与混凝土组合梁、预应力钢与混凝土组合梁和预应力加固钢与混凝土组合梁的受力性能与破坏形态。
The failure modes and the mechanical behaviors of the common steel & concrete composite beam and the prestressed beam and the strengthened beam are analyzed and compared.
试验研究发现,磨削淬硬的磨削力比值范围与磨削淬火钢的磨削力比值范围相一致,大于磨削普通钢的磨削力比值范围。
The grinding force ratio in grind-hardening consists with the grinding force ratio in grinding quenched steel, and is bigger than the grinding force ratio in grinding unquenched steel.
针对不锈钢,合金钢,黄铜,普通钢,铝合金,铸铁不同的材质有不同的油剂。有不同的包装以及各种油剂的标准重量。
For stainless steel, alloy steel, brass, ordinary steel, aluminum, iron different materials have different finishes. There are all kinds of different packaging and finish the standard weight.
渗氮在钢表面获得远远超出正常标准的硬度。其硬度范围为900到1,100布氏硬度,这远高于普通表面硬化所获得的硬度。
Nitriding develops extreme hardness in the surface of steel. This hardness ranges from 900 to 1,100 Brinell, which is considerably higher than that obtained by ordinary case hardening.
在第一部分,学生要用为此特制的实验仪器对一根普通预应力钢杆做拉力实验。
In the first part of the experiment, students will subject an ordinary steel reinforcing rod to a tension test using a testing machine designed specifically for that purpose.
使用状态的组织为细晶粒的铁素体—珠光体,强度比普通碳素结构钢Q235高约20%~30%,耐大气腐蚀性能高20%~38%。
Using the state of the organization for the fine grain ferrite pearlite, strength than ordinary carbon structural steel Q235 about 20% ~ 30%, high atmospheric corrosion resistance of 20% ~ 38%.
与经普通淬火和高温回火的相比,经磁场淬火和高温回火的T10钢的抗拉强度提高了28%,断后伸长率提高了8。
The tensile strength, elongation and hardness of T10 steel subjected to magnetic field quenching and to high temperature tempering were separately increased by 28%, by 8.
采用导电加热切削技术切削淬硬钢的特点在于:可以采用普通机床、硬质合金刀具对淬硬钢进行硬车削加工。
The feature of machining harden steel by means of EHM are: it can utilize the carbide tool to machine the harden steel in engine lathe.
电站锅炉大型化以后,钢构架也变得更为复杂,普通的计算已难以满足要求。
Since power plant boilers have become massive, their steel frames have become more and more complex, hard to be mastered by conventional calculation.
尽管与普通的开瓶器并无二致,但它拥有精良的设计,是由不锈钢和实木制成的。
Despite it being not that different from the typical bottle opener, the BOx does have a nice design made with stainless steel and solid wood.
杂项钢的连接应设计成用普通螺栓?
Connections of miscellaneous steel shall be designed with ordinary bolts.
杂项钢的连接应设计成用普通螺栓?
Connections of miscellaneous steel shall be designed with ordinary bolts.
应用推荐