对左右两侧接触压力影响较小。
更换羊毛？并检查接触压力。
比磨损率也与温度、气氛和接触压力密切相关。
The specific wear rate is strongly dependent on the temperature, atmosphere and contact pressure.
边触式和下触式集电靴装有弹簧用来提供所需的接触压力。
Side and bottom contact shoes are spring loaded to provide the necessary contact force.
推导了组合型密封环的压缩变形量及接触压力的计算公式。
The calculation methods of deformation and contact press force of sealing rings are derived.
清扫器的安装、调整及接触压力等应符合厂家说明书的要求。
The sweeper installation, adjustment and the contact pressure should comply with the requirements of the specification of factory.
在默认模型里，定义摩擦系数为等效滑移率和接触压力的函数。
In the default model the friction coefficient is defined as afunction of the equivalent slip rate and contact pressure.
压力过大会促使密封过早失效，而接触压力过小则会引起泄漏。
Pressure the General Assembly to premature seal failure, and the contact pressure is too small will cause leakage.
在默认模型里，定义摩擦系数为等效滑移率和接触压力的函数。
Thetransition between static and kinetic friction is defined by the values given at intermediate slip rates.
艉轴承弹性模量、径向间隙、厚度对接触压力分布有明显的影响。
The contacting pressure of the stern bearing is influenced with its elastic modulus, radial clearance and thickness.
侧面清洗刷清洗过程中的接触压力经过测试的可靠的均衡技术来控制。
The contact pressure of the side cleaning brush during cleaning can be controlled by the tested reliable equilibrium technology.
对顶进过程中管道纵向与环向钢筋应力及管土接触压力进行了现场测试。
Vertical and annular reinforcing steel bar stress and pipe-soil contact pressure during pipe jacking were monitored on the spot.
在深度方向皮质骨层接触压力最大，在骨孔底部松质骨层接触压力最小；
The maximum occurrs in direction of the medial-distal aspect in cortical bone layer and the minimum the buccal-lingual area on the bottom line in the cancellous bone.
该方法是采取直接测量接触压力分布技术，并与间接测试方法进行了比较。
The technique of directly measuring the contact pressure was employed and the method compared with the indirect method.
研究了轴向坐封载荷与胶筒的峰值接触压力和轴向压缩量之间的变化规律。
The laws between axial set-down loads and maximum contact sealing pressure, and axial compressed displacement were studied.
然而卡瓦和套管间形成非常复杂的接触压力，从理论上直接研究非常困难。
However the contact stress between slips and casing is very complex, it is extremely difficult to study directly in theory.
轧制分离力、轧制力矩以及沿轧辊表面的接触压力也通过有限元法进行评估。
The roll separating force, rolling torque and contact pressure along the surface of the rolls are also evaluated by means of the finite element method.
重点对液压胀管中胀接残余接触压力的几种理论计算方法，进行了讨论分析。
Several theoretical calculation methods for residual kiss pressure during hydraulic tube expansion have been discussed in the paper.
在现代的直缝焊管生产中，轧辊与管坯间的接触压力分布是一个非常重要的参数。
During the modern longitudinal seam welded pipe production, the contacting pressure distribution between the roller and pipe is a very important parameter.
轴承滚针的凸度设计，决定了滚动体与滚道间的接触压力分布，影响其性能和寿命。
Crown Drop of a Needle roller decides the pressure distribution between roller and raceway, capability and life.
利用现有的接触理论和计算方法，在模型的接触处构造了间隙单元来求解接触压力。
The author used the contact theory to found the gap element, and used it to solve the contact force.
而髌骨外侧面软骨接触压力无明显改变，软骨变性不明显，蛋白多糖含量无明显减少。
The remarkable changes of contact stress of patellofemoral joint, the cartilaginous degeneration, and matrix proteoglycan loss not found in the lateral cartilaginous side of patella.
该文建立了自动武器抽壳计算模型，计算出抽壳时药筒与弹膛的接触压力和抽壳阻力。
This paper not only establishes a computing model of the extraction in automatic weapons, but also sets up an extraction measurement system.
该插头结构简单，插头对插座接触压力均匀，其工作可靠性和使用寿命都可以大大提高。
The plug has the advantages of simple structure, uniform contract pressure on a socket, high operational reliability and long service life.
模压压力对接触电阻已有一定程度的影响，但其影响幅度不如接触压力和树脂含量那么大。
The compression pressure and temperature had a smaller influence on contact resistance compared with contacting pressure and PF content.
材料的应力在滚动结果从外在负载下的轴承接触压力以及从附加应力的机械、化工或热性质。
The material stress in rolling contact results from the external loading of a bearing under contact pressure as well as from additional stresses of a mechanical, chemical or thermal nature.
并且使受电弓框架垂向位移和侧滚角度足够小，弓网接触压力达到车辆正常曲线通过时的水平。
In the mean time, the vertical and roll motions of the pantograph fame should be as small as possible, so that to make the contact force as normal as the conventional train.
根据试验观察，提出了一种模拟预应力钢索与索道孔壁接触区域和接触压力的简单、实用的方法。
A simple and practical method was proposed to simulate the contact region and the contact pressure between the prestressed tendon and the wall of ropeway.
计算结果表明，过大的艉轴转角会导致艉轴承接触面积减小，接触压力分布不均，峰值压力增大。
The numerical results indicated that the large misalignment Angle will cause the contacting area of the stern bearing decreased, pressure distribution uneven, and the peak pressure increased.
计算结果表明，过大的艉轴转角会导致艉轴承接触面积减小，接触压力分布不均，峰值压力增大。
The numerical results indicated that the large misalignment Angle will cause the contacting area of the stern bearing decreased, pressure distribution uneven, and the peak pressure increased.
应用推荐