豆腐，谁是后挤压和拉伸食品，还可以压缩和伸展的名字命名。
TOFU, who is named after the squashing and stretching food product, can also squash and stretch.
你的腿可以说是挤压和拉伸了，但是你的关节并没有压缩或扩大。
Your legs can be said to be squashing and stretching, even though the individual joints are not compressing or expanding.
整个面部的挤压和拉伸，在第五和第八帧分别达到极端形状，延迟于眉毛一祯。
The entire head squashes and stretches, hitting extremes on frames 5 and 8, respectively (trailing the brows by a frame).
挤压和拉伸到一个地方复制切断手臂的肉，然后删除原来的手臂的任何部分来完成的效果。
Squash and stretch the meat into place to replicate a severed arm, then remove any portions of the original arm to complete the effect.
关于挤压和拉伸比较重要的一点是无论物体本身怎样形变，它的体积、容积至少要保持不便。
An important note about squash and stretch, is that no matter how an object deforms, it should still appear to retain it's volume.
在写实风格的物体上用许多挤压和拉伸做很卡通的运动也许看起来不可信，在一个漫画风格的物体上做写实般的运动也是这样。
Animating very cartoony motion with lots of squash and stretch on a realistic looking object may not look believable, as would realistic motion on a caricatured object.
研究了挤压比对热挤压AZ91镁合金显微组织和拉伸性能的影响。
The results reveal that the microstructure of the AZ91 alloy is effectively refined after hot-extrusion.
无论是在焊丝方位或部分大小或形状大小的问题上，为使电线尽量减少供给问题和优化焊接性能。EA1400N机器人都会防止弯曲，挤压或拉伸电缆。
Regardless of torch orientation or part size or shape, the EA1400N robot prevents bent, pinched or stretched cables, minimizing wire feed problems and optimizing weld performance.
利用正应力图形和剪应力图形，分析了单向拉伸、拉深及挤压工序中典型点的变形类型及尺寸变化趋势。
In addition, the stress-strain of typical points in simple tension, drawing, and extrusion was successfully analyzed by the figures.
三叠纪，盆地演化经历了一个由拉伸作用形成的断陷盆、构造挤压形成的扰曲盆地和挤压隆升暴露于海面之上的完整构造旋回过程。
In Triassic, the evolution of this basin experienced a complete structural cycle from extended rift basin to compressed flexure one, then rising above the sea level.
当你添加该修改器后，所有弹簧都处于完全硬度状态：没有拉伸和挤压。
Until you add the modifier, all springs are assumed to be perfectly stiff: no stretch and no squeeze.
挤压前均匀化热处理使挤压态合金的晶粒尺寸粗化，拉伸强度和屈服强度降低。
Homogenization treatment before the extrusion coarsened the grain size and reduced the tensile strength and yield strength.
挤压前均匀化热处理使挤压态合金的晶粒尺寸粗化，拉伸强度和屈服强度降低。
Homogenization treatment before the extrusion coarsened the grain size and reduced the tensile strength and yield strength.
应用推荐