串口通信上,实现了故障指令代码的实时发送等功能;
On serial communication, function of real time transmission of failure instruction-code, for example, was realized;
最后通过相应指令代码调用机器人作业,完成叶片空间型面的机器人自动再现及淬火。
Finally, based on correspondence command code transferring to robot operations, the blade space type face of robot auto-reappear and quenching were realized.
但从1963年开始,Kemeny和Kurtz使用他们学会的东西精心编织初学者通用符号指令代码即Basic。
But Kemeny and Kurtz used what they learned to craft the Beginner's All-Purpose Symbolic Instruction Code, or Basic, starting in 1963.
并通过对两种数控系统的编程的比较说明了数控系统指令代码的区别,以及如何针对各数控系统的特点来使用它们。
By comparing of programming, have indicated difference of instruction code and how used them according to characteristic of numerical control system.
研究PMAC程序与标准指令代码的编译,实现了机床执行标准G代码NC程序的功能,解决了NC程序通用性问题。
Researched on the translation of PMAC program and standard code, executed standard G-code NC program, it solved the problem of NC program's versatility.
用C51程序设置对于控制器的读、写状态的时序,从而实现对于控制器的写指令代码、写数据代码、清屏幕、屏幕滚动功能的操作。
C51 program has been set the schedule of reading and writing status for controller. It can work out some operations of writing instruction code, writing data code, clear screen and roll screen.
你可以改变你的代码使用预先性的语法,但一个更好的解决办法是告诉汇编程序,您使用的是性的方式加入“。语法统一”指令代码之前。
You could change your code to use the pre-UAL syntax, but a much better solution is to tell the assembler that you are using the UAL style by adding a ". Syntax unified "directive before your code.
译码单元由指令缓存器和指令译码器构成,针对12位的指令代码翻译成16位控制信号,传送给处理器内部各个部件,用以保证各部件正常工作。
The encoding unit, composed of instruction buffer and command encoder, translates the 12-bit command code to 16-bit control signal, and ensures each part of the system to work steadily.
这些指令被翻译成二进制代码,这是计算机容易处理的一种形式。
The instructions are translated into binary code, a form that computers can easily handle.
如果对代码进行向量化,由于您正在将这些值当作字节进行处理,这意味着每条指令都要一次操作16 个值!
If you vectorize this code, since you are treating the values as bytes, that means that each instruction will operate on 16 values at once!
你可以设置一些寄存器,并发出一个系统调用指令(或中断),并由陷阱处理程序直接调用内核代码。
You set some registers and issue a system call instruction (or an interrupt) and have the kernel code called directly from the trap handler.
通过在其原型机代码中设计的程序,两者都自定义了指令集。
Both had custom instruction sets, with programs designed in their raw machine code.
如果您没有可以生成代码来利用底层处理器架构和指令集的编译器,那么最快的机器也将是无用的。
If you don't have a compiler that can produce code to take advantage of the underlying processor architecture and instruction set, then the fastest machines will be useless.
首先,不应该假定上述赋值语句一定会被编译成一条机器指令,除非亲自验证了机器代码。
First, you shouldn't assume that the above assignment would be compiled as a single machine instruction unless you personally verify the machine code yourself.
早期的程序设计利用机器代码指令在裸机层次上完成。
Early programming was done at the bare machine level, using machine code instructions.
实际上,整个内核没有变,只是增加了新的对象代码和几个函数调用重定向指令。
Virtually the entire kernel remains unchanged, save for the new object code and a few instructions to redirect the function calls.
即使这样改进之后,代码还是会在注释、处理指令和cdata节上出错。
Even with this improvement, your code can still trip on comments, processing instructions, and CDATA sections.
为了消除解释的高性能代价,JIT编译器选择将频繁执行的代码直接转换为CPU的本地指令。
To eliminate interpretation's high performance cost, a JIT compiler selects frequently executed code to be translated directly to the CPU's native instructions.
用JVM的指令形式表示该代码,一般称为字节码,这是下一节要讨论的主题之一。
This code is in the form of instructions for the JVM, generally called bytecode, which is one of the topics for the next section.
注:为引用下列说明中的汇编代码行,我将引用指令地址的最后两个值,因为它们都以054d 20开头。
Note: to reference the lines of assembly code in the following explanation, I refer to the last two values of the instruction address because they all begin with 054d20.
对于某些对象文件格式,调试信息被封装到统称为STAB指令的汇编程序指令中,这些指令分布在生成的代码中。
For some object file formats, the debugging information is encapsulated in assembler directives known collectively as STAB directives, which are interspersed with the generated code.
错误写入处可能是堆,但更糟糕的是,可能写入的是存放代码指令处,因此先前指令会被重写,这样代码执行到中间就无法继续调用了。
The location that is written to can be the heap or even worse, a location where code is stored (so instructions are overwritten) or the stack so your code calls into the middle of nowhere.
您只需要指定事务属性(没有回滚代码或回滚指令!)
You only need to specify the transaction attributes (no rollback code or rollback directives!)
这块代码内的,每一个指令。
If it does, then execute each of the instructions in that block.
清单1的代码演示了如何通过调用方法visitor来添加指令。
The Listing 1 code demonstrates how instructions are appended by calls to the method visitor.
清单1的代码演示了如何通过调用方法visitor来添加指令。
The Listing 1 code demonstrates how instructions are appended by calls to the method visitor.
应用推荐