安装电热带最小弯曲半径为其厚度6倍。
The minimal bending radius is 6 times the thickness of electric heating cable.
此外，可通过改变销轴获得改变弯曲半径。
In addition, by changing pin shaft gain change bending radius.
弯曲半径小，母线架构简明，布置清晰，安装方便。
Small bending radius, simplified busbar framework, clear arrangement, easy mounting.
因此可以用TFBG波长来定义简支梁的弯曲半径。
So the wavelength of TFBG can be used to define the bending radius of simple supported beam.
弯曲半径的调节主要是通过更换弯曲半径的调节轴来实现。
The adjusting of bending radius was implemented by replacing the adjusting axis of bending radius.
根据材料的极限变形，导出管轴临界弯曲半径的计算方法。
According to the limit deformation, a method for calculation of the critical curvature of the tube is developed.
电缆的允许弯曲半径：无铠装电缆，不小于电缆直径的6倍；
The bending radius of cable: non armoured cable, should not be less than 6 times.
由于它的弯曲半径小，大大地降低了安装难度，和缩小了空间尺寸。
The branch cable has small bending radius, which reduces installation difficulty and demands small installation space.
本系统的主要功能有：面内弯曲半径的预测；成形极限的预测；成形工艺的优化。
The main function of the system is in-plane bending radius estimation, forming limit estimation and forming process optimization.
利用光线理论研究光纤弯曲损耗与弯曲半径、纤芯折射中以及包层折射率的关系。
By the theory of ray optics, the bend losses of fiber as function of fiber parameters such as core index, cladding index, core radius and bend radius are set up.
在需要弯曲时，应尽量取弯曲半径大的走向，以降低钢丝绳和护套管间的摩擦力。
When bending needed, better to adopt larger trend of bending radius so as to lower the friction between cable and casing.
半径是0.25，我包铝合金板靠近边缘，以增加预期的弯曲半径，如果有必要的。
The radius is 0.25 and I wrap a aluminum sheets around the edge to increase the desired bending radius, if needed.
通过对板料弯曲变形应力应变分析，提出了几种近似计算最小相对弯曲半径的方法。
A few methods, which approximately calculate minimum relative bending radius, are put forward by analyzing the stress and strain as plate bending deformation in this paper.
在后面章节中，中空板的最小弯曲半径是其厚度的175倍，只可以冷弯，不能热弯。
B. in a later chapter, hollow plate the smallest bending radius is 175 times of its thickness, can only cold bending, hot bending.
推导出限制弯管壁厚变化量的许用最小弯曲半径公式，经试验验证具有一定的实用价值。
At last, the formulation of allowable minimum bending radius limiting the change of the tube-wall thickness is derived, and proved to be of practical value.
弯曲半径可根据所给表格选50- 600 mm，行程小的可相应选择较小的半径。
Bending radius can choose according to form 50-600mm, a journey of small can corresponding choice of smaller radius.
通过对模拟结果的分析，研究了硬化指数、弯曲半径、材料厚度等因素对回弹的影响规律。
By analyzing the simulation results, how the hardening parameter, bend radius parameter and thickness parameter influence springback is studied.
通过生产实践观察和理论分析，阐述了矩形磁极线圈弯曲半径对弯角部位形状尺寸的影响。
Through the observation to the practical production and analysis with the theories, the influence of bend radius inside the rectangle pole coil against dimension of the bend corner part is discussed.
计算了有效弯曲半径经历渐变和突变情况下，模式功率随传播距离和有效弯曲半径的关系。
The dependences of mode power on propagation distance, effective bend radius are calculated with the bend radius experiencing sudden and gradual transition.
介绍在电力行业设备安装、检修过程中管道等径弯头任意角度、任意弯曲半径的展开计算方法。
The paper introduces the developed calculation of the arbitrary Angle yoke of equal radius in the process of installation or repair of the pipes.
介绍在电力行业设备安装、检修过程中管道等径弯头任意角度、任意弯曲半径的展开计算方法。
The paper introduces the developed calculation of the arbitrary Angle yoke of equal radius in the process of installation or repair of the pipes.
应用推荐