图7所示为带状引线连接芯片和管壳装配的工艺程序。
Figure 7 shows the sequence for tape bonding the chip and assembling the package.
内引线连接是微电子器件制造过程中的重要环节之一。
Chip interconnection is an important part in the microelectronics parts manufacture process.
该光盘还包含至少一个线性天线振子，它例如经电极引线连接到转发器，并在数据区内延伸。
The optical disk further comprises at least one linear antenna element coupled to the transponder, e. g., via pole lead (s), and extending within the data region.
与数字多用表不同，微欧姆计没有内部电阻器(RS)，所以四条引线都要连接才能进行测量。
It doesn't have the internal resistors (rs), as in the DMM, so all four leads must be connected to make a measurement.
温度传感器，启动开关s1的，和电流控制电位器都连接到局用伺服引线(可在许多商店的嗜好，在10英尺长度)。
The temperature sensors, start switch S1, and current control potentiometer are all connected to the board using servo lead wire (available at many hobby shops in 10 foot lengths).
传感器引线及其保护层应为一体化结构，与变送器模块的连接应采用厂家提供的标准。
The lead wire and its protective layer of the sensor shall be of one-piece construction, and its connection with variable conveying module shall subject to the Manufacturer's standards.
频率控制和选则用表面安装的压电器件。标准外形和终端引线的连接。第1部分：塑料模压外壳外形。
Surface mounted piezoelectric devices for frequency control and selection - Standard Outlines and terminal lead connections - Part 1: plastic moulded enclosure Outlines.
安装入面板边的将是连接遥控电缆的多引线的接线盒。
Mounted into the side of the panel will be a multi-pin electrical connector to connect the remote control cable to.
连接头为终端嵌块或者发射机提供一个受保护的、洁净的区域，从温度感应器到引线。
Connection heads provide a protected, clean area for mounting a terminal block or transmitter as part of the transition from temperature sensor assembly to lead wire.
在微电子中，使用电线将数据包的引线与芯片上的结合区相连接的过程。装配过程的一部分。
In microelectronics, the process of connecting wires from the leads on the package to the bonding pads on the chip. Part of the assembly process.
坚固的镀镍铜夹引线时，不会引发最初连接到电池，以减少爆炸的可能性。
Rugged nickel-plated copper clip leads won't spark when initially attached to a battery to reduce the possibility of an explosion.
多个导电内引线被接合至该区域周围的基片，以连接至该半导体晶片。
A plurality of electrically conductive inner leads are bonded to the substrate around the area for connection to the semiconductor die.
引线电连接探测部分，并在外壳的轴向另一末端向外伸出。
Lead wires are electrically connected with the detecting section and outwardly extend through an axially other end side of the casing.
严格保证电源正负接线与控制器的正负引线对应连接正确，否则将会烧坏控制器。
Ensure that the positive and negative power supply leads are correctly connected to the corresponding positive and negative controller leads, otherwise the controller will be burned.
这些引线通过按压连接器（10）连接到电门和接受器引线，并通过乙烯基管（11）绝缘。
These lead wires are mated to the switch and receiver lead wires by press-on connectors (10) and are insulated by vinyl tubing (11).
采用新传输设备范围内的光纤电缆来连接初级保护1引线保护系统通信。
The communication link for the primary 1 pilot relay system will be by means of fiber optic cable which is in the scope of New Transmission Facilities.
能够通过焊锡良好地固定下部IGBT和上部IGBT，同时牢固地连接下部IGBT和引线，形成可靠性高的半导体器件。
A lower IGBT and an upper IGBT are excellently and firmly bonded by solder, the lower IGBT and a wire are firmly connected, and a highly reliable semiconductor device is formed.
接头界面有效连接面积和接头上引线横截面变形量的变化分别是造成接头电阻波动性和整体增大趋势的原因。
The real contact area of the bond interface and the cross-sectional deformation of the bond wire were the causations respectively for the fluctuation and wholly increase of the resistance.
这些要求所指的内部电线，是指从器具电源线入口处，或从用于连接电源线的接线端子或引线处的互连线，即使有些为电源线导线。
Leads for power-supply connections of a fixed appliance, even though some of this may be in the form of flexible cord.
使用短长度的伺服引线与布朗（或黑色）带头拆掉，连接中一至洞，标志着中一对董事会。
Using a short length of servo lead wire with the brown (or black) lead removed, connect S1 to the holes marked S1 on the board.
本产品与变频器连接的电机引线或其它有较高屏蔽要求场合使用。
This product is used for connecting motor and frequency converter of some other places where higher shielding performance is required.
这导致引线框架和检测元件 之间的具有改善的电连接状态。
This results that the lead frame and the detection element have improved electrical connection.
在二次电池的阴极引线与阳极引线之间平行连接各恒定电压元件和MIT元件。
Each of the constant voltage element and the MIT element are connected in parallel between a cathode lead and an anode lead of the secondary battery.
设计成只有两条引线的器件有的时候很难进行四线连接。
It is sometimes difficult to make a four-wire connection to a device designed for just two wires.
设计成只有两条引线的器件有的时候很难进行四线连接。
It is sometimes difficult to make a four-wire connection to a device designed for just two wires.
应用推荐