基于对引信设计的可生产性考虑，开发了工艺与成本分析软件。
The process and cost analysis software is designed for producibility of fuzes .
火炮弹丸内弹道特性和中间弹道特性对于引信设计而言十分重要。
The interior ballistic and the intermediate ballistic characteristics of artillery projectile are very important for fuze designing.
基于对引信设计的可生产性考虑 ，开发了工艺与成本分析软件 。
The process and cost analysis software is designed for producibility of fuzes.
最后，为了便于工程应用，作者又对连续波多普勒引信设计了图形用户界面。
At the last, the author design the GUI of CW fuze to convenient for the engineering application.
如何在满足一定启动概率的前提下，解决好目标识别和抗干扰这一对矛盾是激光引信设计必须面对的问题。
How to settle the conflict between target identification and anti-jamming on the premise of meeting certain probability of fuze actuation is a major problem faced on any laser-fuze designer.
提出并分析引信设计库及相关信息资源集成系统的四层结构模型：支撑层、网络层、系统集成层和工作应用层。
In this paper, the information integrated system for fuze design, with four layers structures, is studied and presented.
一些是标准设计问题，比如颜色要形成足够的对比度、在版面中提供足够的指引信息以及在内容的逻辑区域周围安排足够的空白。
Some are standard design criteria, such as creating enough contrast in your colors, providing enough leading in your typography, and placing enough white space around logical areas of content.
结果提出了引信智能化设计的基本思想。
Results The basic idea of intelligent design was presented in fuzes.
通过对引信软件可靠性的需求分析，总结了引信软件的可靠性设计方法、引信软件可靠性的基本设计准则和详细设计准则。
By analyzing the requirement of fuze software reliability, fuze software reliability design methods, fuze software reliability basic and detail design criterions are summarized in this paper.
论述了冗余设计技术在引信安全系统中应用的重要意义和前景。
The significance and prospect of the application of redundancy design in fuze safety systems is discussed.
炮弹引信炮口保险性能是一项重要的安全性能，因而其设计指标也一直是广泛关注的焦点。
The muzzle safety of a projectile fuze is an important safe performance, so its designing requirements are widely given ones attention to.
这种理论和方法对引信系统的设计具有普遍意义。
This theory and method will be universally available to the design of fuze system.
本论文主要研究了利用微处理器技术、串行EEPROM存储器技术等设计电子时间引信系统的方案。
In this paper, the method that how to design electronic time fuze system by use of MPU technique and EEPROM technique is mainly researched.
针对打击目标，从侵彻弹引信的要求出发，设计出一种实用的混凝土破坏弹引信电路。
Aimed at the shot object, a practical fuze circuit of projectile to destroy concrete is designed.
并对引信的总体结构、有关电路的设计及其存在问题进行了探讨。
The general structure of fuze, the design of relating circuit and the existing problems are discussed in this paper.
该原则适用于一般曲折槽式保险机构的设计，对于引信瞎火事故分析具有普遍指导意义。
It is suitable in the design of general fuze zig-zag devices and has a guiding significance when analysing accidents caused by misfiring of fuzes.
文中结合遥控装定引信电路设计，给出了实现抗高过载、小体积、低成本和低功耗的具体方法和措施。
Combining the design of remote setting fuze, the dissertation presents the concrete means and measure to realize high over loading, small bulk, low cost and low consumption.
炮弹引信炮口保险距离设计指标不但与弹丸威力有关，还涉及弹丸初速。
And the design requirements of the muzzle safe distance of the projectile fuze are concerned with not only the power of the projectile, but also its muzzle velocity.
根据被动磁引信工作特点，设计了基于三维磁阻传感器和DSP的铁磁性目标探测与定位系统。
According to the passive magnetic fuze operational characteristics, the ferromagnetic target detecting and locating system based on tri-axial magnetoresistive sensors and DSP was designed.
同时，还对其它几种体制引信干扰波形的设计作了相应的探讨，并提出了几种特殊的干扰波形设计方案。
At the same time, some other kinds of fuzes jamming wave also be discussed in the paper, and give the project of some special kinds of jamming wave.
当引信结构允许设计较大的增阻面积时，选用简单的平面阻力器结构较为合理。
It is concluded that selecting a plane damper structure is more reasonable when the fuze structure allows larger increase in its area.
引信安全性设计是引信的核心技术之一，引信安全系统是引信安全性设计的主要体现形式。
The fuze safety system is not just an absolute sub-system in fuze, and is not equivalent to safety and arming device.
其研究结果对引信电磁兼容性设计具有一定的积极作用。
The results obtained in this paper have positive effect on fuze EMC design.
针对引信信号处理严格的实时性要求，本文讨论了用单片数字信号处理器(DSP)进行引信信号快速处理设计的应用问题。
In this paper, according to the strict real time requirement of the signal processing of a fuze, the application of the single chip digital signal processor (DSP) in the fuze design is explored.
结果表明，这种是电路设计可以较好地解决PD引信防早炸问题。
It is proved that the circuit design can perfectly resolve the early explosion of PD fuze.
在脉冲多普勒数字化引信的基础上，详细设计了可编程脉冲发生器、数字化接收机和数字信号处理机。
In the basis of pulse Doppler digital fuze, the programmable pulse generator, digital receiver and digital signal processor are designed in detail.
经过特征提取用于引信的设计中，可作为引信发射环境识别的有效手段。
These information can be used for fuzes design to improve fuzes environments recognize ca.
对引信电源模块进行了设计实现。
对引信电源模块进行了设计实现。
应用推荐