这意味着直线是平行于平面的。
吸气上面手臂起来，平行于地面。
平行于穿孔卡短边的一行穿孔位置。
A line of punch positions parallel to the shorter edges of a punch card.
裂纹在近乎平行于表面的方向上生长。
也就是说直线，实际上是平行于平面的。
OK, so that's what would tell you that the line is actually parallel to the plane.
它是过射影中心且平行于象平面的平面。
It is the plane through the center of projection parallel to the image plane.
另外，叶片轮的平面平行于极轴，这被称作是逆风设计。
In addition, the plane of the blades is parallel to the pole. This is called an upwind design.
另外，叶片轮的平面平行于极轴，这被称作是逆风设计。
In addition, the plane of the blades is parallel to the pole.This is called an upwind design.
在中周期，通常是日线图，平行于均线画通道。
We draw them parallel to the moving average in the intermediate timeframe, usually daily.
实际上，此时直线平行于平面，或者就在平面之上。
So, indeed our line could have been parallel to the plane or maybe even contained in the plane.
如果我只观察平行于x轴的切面，那这应该是一个极小值点。
If I look only at the slice parallel to the X-axis then maybe I am going through the minimum.
我们只需要考虑一个平行于圆柱母线的窄条的变形。
We need to consider the deformation of only one strip parallel to generatrix of the cylinder.
最简单的会是，首先沿x轴到,然后平行于y轴走。
The easiest of all, probably, is to just go first along the x-axis to and then go up parallel to the y-axis.
因此，在平行于狭缝两端边界的方向上，几乎没有什么。
There will therefore be very little diffraction parallel to the edges of the slit.
我们要做的就是…，在这张图片里，用平行于yz平面的。
So, what I'm going to do is I'm going to take planes, say in this picture, parallel to the yz plane.
一个曲面和平行于射影平面的一个平面的交线到某个平面的射影。
The projection onto a plane of the intersection of a surface with a plane parallel to the projection plane.
平行于西南立面的狭小通道连接着半覆盖的庭院和住宅的入口空间。
A catwalk parallel to the southwest facade extends through a semi covered courtyard into the entrance of the house.
圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线。
A conic section whose plane is not parallel to the axis base or generatrix of the intersected cone.
当沿着一条平行于直线36的线向下观察时，线性阵列如图2d所示。
The line array appears as FIG. 2d when viewed downwards along a line parallel to line 36.
对于给定的x，我们要做的就是，用平行于yz平面的平面去切图像。
OK, and for a given value of x, what we will do is we'll slice our graph by this plane parallel to the yz plane.
当沿着平行于轴线的直线并且面向锥体观察时，线性阵列如图2C所示。
The line array appears as FIG. 2C when viewed along a line parallel to the axes, facing the cones.
他们测量其平行于层的电阻，发现它放置在一个磁场干扰的地方时下降了约1.5%。
They measured the electrical resistance parallel to the layers and found that it dropped by about 1.5% when they placed it in a magnetic field.
提示：确保你的前臂平行于地面，你的肘关节贴着你的身体，腕关节伸直。
TIP: Be sure to keep your forearm parallel to the ground your elbow by your side and your wrist straight.
提示：确保你的前臂平行于地面，你的肘关节贴着你的身体，腕关节伸直。
TIP: Be sure to keep your forearm parallel to the ground, your elbow by your side, and your wrist straight.
因此我使x等于一个常数，那就是说,用一个平行于黑板的平面来进行切割。
OK, so I fix x equals constant. That means that I slice by a plane that's parallel to the blackboard.
在平行于放置被摄物体的位置上把有距离标尺的测试图表放置于一个斜面上。
Next to the parallel target, a patterned chart with a distance scale is placed on an incline.
表明信用评级是一种解决非对称信息问题的手段，这种手段平行于激励理论。
It is shown that credit rating is a way to solve the problem of asymmetric information, different from incentive theory.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
应用推荐