而且我也开创了我自己的T恤品牌，自己做一些工艺图印在T恤上。
But I've actually also started my own T-shirt brand, it's all my artwork.
模具检验：模具制作完毕后，由模具检验员按照铸造工艺图对模具进行检验。
Pattern inspection: the pattern inspector should examine the pattern as per casting process drawing after pattern completion.
在扎染制品CAD系统开发中，从设计效果图到生产工艺图的自动转换是一个十分重要的问题。
It is an important problem to convert designed effect drawing to techniques picture in the department of Zaran CAD system.
请看安装位置工艺流程图。
粉末冶金(图5.1)采用烧结工艺将金属粉末制成各种各样的零件。金属粉末放在封闭的金属腔(模具)中在压力下被压实。
Powder metallurgy (Fig. 5.1) USES sintering process for making various parts out of metal powder. The metal powder is compacted by placing in a closed metal cavity (the die) under pressure.
介绍了系统构成和工艺流程，给出了部分系统流程图及提高安全生产的各项措施。
It describes the system structure, a part of system flow chart. It provides some measures for improving produce safety.
根据系统通用化的需要编制了“压缩机工艺流程图快速生成系统”。
'Rapidly create system of compressor technical process drawing' is finished to meet the need of generalization.
原动机驱动在汽缸内的活塞，交替地吸入和排出工艺流体（图）。
The driver moves the piston inside the cylinder, alternately pulling in and pushing out the process fluid (Fig. ).
图7所示为带状引线连接芯片和管壳装配的工艺程序。
Figure 7 shows the sequence for tape bonding the chip and assembling the package.
图3 - 2说明了在一些普通切削成型加工工艺中，切削刀具和工件之间必要的关系。
Figure 3-2 illustrates the necessary relationship between cutting tool and the workpiece for chip formation in several common machining processes.
钢的焊接CCT图，是正确选择焊接材料、确定最佳焊接工艺、消除焊接裂纹、制订焊后热处理规范的重要依据。
Welding CCT diagrams of steels are the basic to select welding material, determine the optimum welding technology, relieve welding cracks and lay down standard of past heat treatment.
通过工程计算，设计出工艺流程图及光合细菌反应池、二沉池和海藻塘的工程容量。
By engineering calculating, the flow chart and the engineering capacities of the main PSB reaction tank, the secondary setting tank and the seaweed pond are obtained.
介绍了根据工艺要求系统地构成状态表和程序图，写逻辑表达式。画控制线路的具体方法。
It can be used to systematically construct state array and sequence diagram, write logic expressions, and draw control circuit diagram based on technical requirements.
了解零件图作用与内容，了解典型零件表达方法及常见工艺结构。
Understand the functions and contents of detail drawings. Understand representation methods of typical parts and common process structures.
这些流程图描述着每道工艺的衔接情况。
该系统能进行尺寸链解算，计算工时定额，绘制零件工序图，打印输出零件工序卡和工艺路线卡。
The system can solve dimensional linkage, calculate man-hour quota, make operation drawing, and print out the operation sheet and the process route sheet of a part.
同时给出了三个储粮生态区域低温储粮优化方案的工艺流程图。
The flow charts of optimum scheme for low temperature grain storage in three ecological areas were provided respectively in this paper.
其它内部连锁、安全保护功能。控制柜带图介工艺流程图。
Other internal interlocking and safety protection functions. The control cabinet shall be supplied with drawings and the process flow chart.
采用石雕、浮雕与花板雕刻相结合的技法，根据题材内容和色彩要求，配石成图，精制成多种工艺美术品。
Use of stone carving, relief carving and flower plate combination of techniques, according to subject matter and color requirements, with Ishinari map, refined into a variety of arts and crafts.
开发工艺概念图以满足预期销量，包括缓冲，提速的技术可行性和节拍时间来支持财务规划的销量。
Develop process concept to meet volume aspirations including buffer, technical availability overspeeds and Takt time to support financial planning volumes.
本系统主要由标准件工艺数据库、工序图生成和人机交互界面等三个部分组成。
This system consists of the process database of standard parts, formation of process pictures and the user-interface.
本文介绍了利用交互性计算机绘图技术，绘制粮食工厂工艺流程图的方法和意义。
The method and importance of making flow chart of technological process in grain mills by interactive computer graphics are presented in this paper.
经过大量计算，总结出二冷水量的计算公式和操作工艺参数图。
The calculation formula on the volume of secondary cooling water has been derived, and profile of process para - meters drawn from the enormous calculated datum.
根据数控铣削的加工特点，提出零件图工艺分析的要点。
The paper presents the main points of technological analysis in detail drawing based on machining feature of NC-milling.
在设计中具体分析了掺混控制系统的结构，控制方式，工艺流程图和软硬件设计。
The structure of the control, the control scheme, flowchart and the design of hardware and software are analyzed concretely.
本文首先给出了卷烟厂制丝车间工艺流程图，并分析了制丝工艺的质量因素。
In this paper the technological process flow chart of cut tobacco workshop is presented and the quality factors of making cut tobacco are analyzed briefly.
在对规程进行认真分析后，画出工艺流程图，并据此进行设备选型。
After proceeding the earnest analysis to the rules distance, draw the craft flow chart, combine to proceed on these grounds the equipments choose the type.
对选矿工艺设备配置图的有效描述及算法，是实现选矿厂计算机辅助配置设计的关键问题。
The key problems of the concentrator computer aided layout are how to carry out the effective demonstration and algorithm of the equipment layout of mineral processing.
对损伤、故障、检验和修理工艺流程图等问题进行了分析讨论。
Some issues at items such as damage, failure, inspection and repairing technology flow diagram are discussed.
对损伤、故障、检验和修理工艺流程图等问题进行了分析讨论。
Some issues at items such as damage, failure, inspection and repairing technology flow diagram are discussed.
应用推荐