结果表明，蜗室中间的主流速度在不同转速下均呈抛物线型分布；
The results clearly document that the curves of vertical and main velocity in the middle area of the volute are parabolic at all running speeds.
能自动在不同转速下循环完成进料、分离、洗涤、卸料等工序，可实现远、近距离控制。
The machine can feed, separate, wash and discharge repeatedly at different rotating speeds. They can be controlled nearby or in the distance.
图中实线表示发动机在不同转速下能提供的最大转矩，而虚线表示负荷变动时压缩机正常工作需要的转矩。
The figure that the solid line at different engine speeds to provide the maximum torque, while the dotted line that the normal load changes in the work of the compressor torque needed.
此控制器根据电机在不同转速下的输出信号，经过数字处理，提供给电机适当的电流和频率，使之达到超静音，同时使电机能发挥最大的转矩和最高的效率，从而使电机动力强劲。
The controller processes the motor output signal digitally, and provides suitable current and frequency to the motor to make it silent and efficient, hence enhance the power of the motor.
根据车用发动机的实际使用工况，在不同转速及爆发压力下对其进行动力学计算，得到发动机的表面振动速度级。
According to the actual operational condition of engine, calculate dynamics with different rotational speed and breakout pressure, and get the surface vibration speed stage of engine.
施加不同的预压力在低、高真空环境下对超声电机的转速、转矩及温升进行测量并与常态下相比较。
By applying different pre-pressure, the speed, torque and temperature of the ultrasonic motor in low and high vacuum have been tested and compared with the normal condition.
飞轮控制系统是个多回路系统，内回路为电压稳定回路，外回路在不同的工作模式下分别为电流回路和转速回路。
Flywheel control system has two closed loops, the inner is voltage stabilization loop, other is current loop or is speed loop in different mode.
本文研究了在不同作用时间、不同工件转速、不同入射角度等条件下离子束对CLBO晶体抛光表面的处理效果。
Ion beam etching (IBE) was applied to treat the as-polished surfaces of a CLBO crystal with varying in rotation speed of clamp, etching times and incidence angles.
本文用参数变异法给出串激直流电动机在不同转速情况下的运动方程的解析解，以拓宽人们分析这类问题的思路。
In this paper, parametric variation method is used in kinematic equation of series excitation direct current motor with different turning velocities.
对电流变夹层梁在不同电场强度与旋转速度下的振动响应特性进行了实验研究。
The vibration response performances of the rotating beam with respect to the intensity of the electric field and the rotating speed are presented.
在德国产流化床式AF G- 100气流磨内，对同一物料在不同分级轮转速条件下及不同物料在同一分级轮转速情况下，粉碎分级出的颗粒大小进行分析研究。
This paper studies particle size of both the same and different materials which were milled, graded and processed under different conditions, in AFG-100 gas stream mill made in Germany.
通过动态调整油泵齿条位置实现对柴油机突变负载下转速的闭环控制，从而保证在不同工况下转速的稳定性。
By adjusting dynamic fuel pump rack position, closed loop of engine speed in suddenly changing of load was realized in this model. It could keep engine speed stability in different status of engine.
从而取得在不同转速、不同位置、不同通讯速率下的误差曲线，进而直观地认识容栅编码器的静态和动态精度。
According to different rotatable velocity, location, communication velocity, I draw the error curves to give a concrete description of grating-shape capacitive coder dynamic and static precision.
初步解决了在相同或不同转速下，两条端面曲线啮合的条件。
Also, the solution to the intermeshing condition of the two cross section curves under either same or different speeds is provided. Cross section curves for practical instants are plotted.
对各典型状态滚动轴承在不同转速和载荷下的声发射信号进行了振动分析，研究了滚动轴承的损伤振动随转速和载荷的变化规律。
Based on the vibration analysis of AE signals under varying load and rotating speed, the patterns of damage vibration of rolling element bearings under varying load and rotating speed were researched.
对行星式球磨和搅拌式球磨氧化锌在不同活化时间及不同转速下储能结果进行了比较。
The calorimetric results indicate that mechanically activated zinc oxide can release the storage energy during calorimetric process.
对行星式球磨和搅拌式球磨氧化锌在不同活化时间及不同转速下储能结果进行了比较。
The calorimetric results indicate that mechanically activated zinc oxide can release the storage energy during calorimetric process.
应用推荐