通过正交综合实验，确定了较合适的喷涂工艺参数。
And the optimum electric arc spray parameters were obtained through comprehensive experiment.
选择不同的喷涂工艺参数，在镁合金表面喷涂铝锌丝材。
Different technological parameters of electric-arc spraying aluminum and zinc on the surface of magnesium alloy samples were selected.
探讨电弧喷涂工艺参数变化对涂层组织、抗折弯性能的影响。
The effects of parameters changes of electric arc spraying technology on coating structure and anti-buckling performance were discussed in this paper.
选择喷涂工艺参数的主要原则是提高涂层与基材的结合强度。
Choose spraying process parameters are the main principles of the coating and improve the bonding strength of the substrate.
介绍了喷涂工艺参数对孔隙率影响及涂层形成过程的数值模拟。
The effect of processing parameters on porosity and the modeling of coating formation are introduced.
实验研究分析了添加炭粉造孔剂和改进喷涂工艺参数对阳极层孔隙率的影响。
The influence of added charcoal pore-forming agent and improved plasma spraying parameters on porosity of the anode layer were investigated experimentally.
着重试验研究了耐磨、抗蚀涂层材料的设计配制、性能优选和喷涂工艺参数的选定。
The study was focused on the layer's composition design, tribological properties, and spraying process parameters for wear and. corrosion resistance.
对比研究了新型轴向送粉等离子涂枪和普通等离子喷涂枪的喷涂工艺参数和制备涂层的性能及其组织。
In this paper, the axial-fed plasma spraying gun was used to obtain ceramic coatings on steels. Its parameters, properties and microstructure were compared with those of a traditional one.
采用正交设计方法和通过极差分析研究了电弧喷涂工艺参数对J CW - b涂层结合强度和耐磨性的影响。
The influence of arc spraying parameters on the adhesive strength and wear-resistance of JCW-B coating was studied by orthogonal design test and extreme analysis.
讨论了喷涂氨基锤纹漆的工艺参数、施工要点、漆膜质量及产生漆膜弊病的原因。
Process parameters, application essentials, film quality and reasons causing the film objections in spraying amino hammer paint are discussed.
对实际系统进行了喷涂工艺试验，给出了不同工艺参数条件下，采用红外测温仪进行皮膜温度检测的试验结果和理论分析。
Through the experiments with different process parameters, the result of the coatings temperature measurement with the infrared thermo scope and its theoretical analysis were given.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用电弧喷涂方法在Q 235钢基体上喷涂铝涂层，并用正交设计的方法对工艺参数进行了优化。
Aluminum coatings were sprayed onto the substrate of steel Q235 by arc spraying method and the processing parameters were optimized by orthogonal experimental design.
本文介绍玻璃钢头盔静电喷涂的原理、装置及工艺参数的选择。
The article introduces the principle, apparatus and selection of technological parameters in the electrostatic spraying of FRP helmet.
讨论了锌系工件喷涂的相关工艺、现场管理、技术参数、质量检验和环境要求等。
Relate process, management on the spot, technology parameter, quality test and environmental requirements of spraying powder paint on the zinc components are discussed.
介绍了单头空气喷枪、空气静电喷枪、高速旋杯式静电喷枪各自的工作原理、施工特点及影响喷涂质量的工艺参数。
The working principles, characteristics and process parameters of single head air spray gun, air electrostatic spray gun and high-speed rotated cup type electrostatic spray gun were introduced.
通过分析，得出各个工艺参数对涂层性能影响的定性结果，在可得到涂层的工艺范围内，喷涂电流对涂层性能的影响最大。
It is concluded that the coating performance depends most on the current through the qualitative analysis of the effect of process parameters on the coating performance.
用此工艺参数修复船用不锈钢油冷套，加之合理的喷涂工序与材料匹配，达到良好的修复效果。
A good repairing result was obtained by combining reasonable spraying process and material matching with this parameter in repairing oil cooling set of stainless steel.
本文阐述了喷涂工艺流程及参数。
In the paper the spraying process and parameters are described.
最后研究了空气喷涂和静电喷涂两种施工方式的工艺参数。
Finally, the application parameters for air spraying and static spraying were researched.
提出了氧乙炔焰铝丝喷涂普碳钢灼勺工艺及适宜喷涂参数。
This article expounds Al coating technology and parameter chosce by analysing the oxyacetylene heat Al coating of iron frying Pan.
结果表明，影响涂层性能的工艺参数主要是电弧电流，其次是喷涂距离和雾化空气压力。
The results showed that the main parameters influencing the coating properties are the arc current, spraying distance and air pressure.
结果证明 ：在所定的工艺参数下 ，等离子喷涂层组织呈层片状 ，层间为机械结合界面 ；
The results show that structures of plasma sprayed coatings are lamella in shape, mechanical bond in interface regions.
结果证明 ：在所定的工艺参数下 ，等离子喷涂层组织呈层片状 ，层间为机械结合界面 ；
The results show that structures of plasma sprayed coatings are lamella in shape, mechanical bond in interface regions.
应用推荐