提出桩的合理布形式,及中间桩的受力计算方法。
The reasonable laying-pile shape and calculating method will be presented.
斜拉桥的施工过程的受力计算是斜拉桥设计的重要组成部分。
Construction procedure calculations are important parts of the design of cable-stayed Bridges.
但对抛物线斜板拱桥的受力计算尚无成熟理论,使之应用受到限制。
However, it is restricted in application owing to the lack of a sound theory about the calculation of force of the parabolic oblique arch bridge.
以实例分析了抗震设计中桩基受力计算过程,并得出结论,提出建议。
This paper analyzes the calculation process of the forces on pile foundation in seismic design, obtains some conclusions, and advances some suggestions.
并介绍内抱杆组立铁塔施工技术、施工工艺、受力计算和工器具选择。
It describes that tower construction technique, process, strength calculation and apparatus selection by using the internal gin pole.
本文介绍将线路铁塔整体提升平移的受力计算及其在实际施工中的应用。
The author introduces the strength calculation of lifting up and moving the whole iron tower and Us application m engineering construction.
目前对于十字头万向接轴整体式轴承座键槽的受力计算尚无简便确切的方法。
So far there has been no simple and correct calculation approach available for computing the stress distribution in the key slot on the integral cross pin type journal bearing rest.
该模型的建立将对疏水沉降矿区井壁的受力计算和井壁破裂预测具有现实的意义。
It has some real meaning for stress calculating and fractures zone forecasting on shaft wall in drainage settlement coal field.
本文系统介绍了动态轻压下技术的轻压下控制模型和相关设备的受力计算、校核。
In this paper, dynamic soft reduction model and stresses calculating and calibration of the main equipment of dynamic soft reduction have been described.
针对客车车身结构的受力计算,本文提出了一种更符合实际结构的薄壁偏心梁单元。
For calculating stress of BNS body structure, a thin-walled eccentric beam element witch accords with demands is introduced in this paper. The eccentricity existing in truthful structure.
文中介绍了三水二桥主桥上、下部结构设计特点,及对主桥结构进行了受力计算与分析。
This paper introduces the design characters of superstructure and infrastructure of Sanshui Second bridge. The main bridge structure and mechanical calculation are introduced too.
按照我国现行规范的规定,作者编制了船舶舱面集装箱及其系固设备受力计算与校核系统计算程序。
According to the present Chinese criteria, the authors have completed a program for calculating and checking the forces acting on containers on deck and their securing devices.
基于一般链传动的受力计算,分析了模切机链条运行过程中所受的张力和附加动载荷,可供设计时参考。
Based on the calculation to the common calculating chain force, this article analyzes the tensile force and additional dynamic load which the China of mould-cutting machine stands in the movement.
本文利用SAP5结构分析程序按照三种不同的计算模式,进行底架的受力计算,并与实测值进行对比。
Using structure analysis program SAP5, this paper represents load calculation of chassis frame with 3 different calculation modes and compares calculation results with those of experiment.
运用计算软件ANSYS,采用围岩—结构模式,对TBM施工隧道仰拱预制块进行模拟动态施工的受力计算研究。
A simulation of dynamic forces acting on invert prefabricates in TBM construction tunnel is made with surrounding rock-structure model by using ANSYS software.
分析HXD1型机车牵引座的螺栓连接方式中的特殊点及其机理,并通过受力计算说明了衬套对螺栓使用可靠性的影响。
This paper analyses the special points and mechanism of bolt connection mode on type HXD1 locomotive traction base, and shows the effect of bush to bolt application reliability by stress calculation.
通过对路面铣刨机铣削装置的工作方式、工作原理、刀具布置和铣削运动的理论分析,建立了刀具铣削受力计算的数学模型。
Based on the theoretical analysis of operating mode, operating principle, cutter arrangement, and milling motion of pavement miller, the mathematical model of cutting resistances has been established.
利用该方法对苏通大桥进行整体受力计算,得到钢箱梁板件的横桥向和顺桥向应力,分析了钢箱梁顶板应力在横桥向的不均匀性。
Mechanics behaviors of Sutong bridge were computed by this method, and longitudinal stress, transversal stress of plates of the girder and section stress distribution were discussed consequently.
介绍根据不同的塔型、地形和交通状况,选择合适的组塔方案,配备合适的组塔抱杆,并探讨内抱杆组立铁塔施工技术、施工工艺、受力计算和工器具选择。
This paper mainly introduces the choice of the proper schemes for assembly tower and adequate gin pole according to different type of towers, topography and transportation condition.
简要介绍了某投放装置在做地面发射试验时发生粘着磨损的故障情况,通过受力计算和理化分析,确定了是由于锁制钩和承力轴发生粘着磨损所致,验证试验中故障复现。
By mechanics calculating and physicochemical analyzing, the reason is found that it results from the cohesive wear between the detent hook and forced shaft, and reappears in validate test.
使用有限元软件ANSYS,把熔体流动计算结果作为参数,计算了枝晶的受力状态。
Based on FEM software ANSYS, the dendrites stress states are computed using the results of the melt flow as computing parameters.
应用有限元法对辽河滩海油田大斜度定向井抽油杆柱受力进行了三维计算。
Using finite element analysis method, three-dimensional calculation is conducted for force summing on rod in high-inclination well of Liaohe tidal zone oilfield.
提出了双目标模型中粒子的电荷和受力的计算公式,引导不可行粒子转化为满足约束条件的粒子;
The computational equations of the charge and force exerted on the particles are presented for the bi-objective model, which will lead the infeasible particles to transform into feasible ones.
为桩锚支护结构施工进程中受力变形的设计计算和过程控制提供了动态计算模型。
What we have done here provides developing calculation model for the force-deformation calculation and process control of PARS during construction.
本文针对体外预应力混凝土简支梁的受力、变形特点,提出了计算体外预应力结构中收缩徐变产生的预应力损失的基本方法。
The paper provided with a method to calculate the pre-stress loss caused with systolic stress in the outside of pre-stress force.
文中阐述了该封闭传动的特点,传动比计算,受力分析和效率计算。
First the major Characteristics of this transmission, calculation of ratio, analysis of forced and calculation of efficiency are given.
本文介绍了轴销剪切式称重传感器的结构与特点,受力分析与理论计算。
This article introduces structure, characteristic, stress analysis and theoretical calculation of shaft pin cutting type load cell.
本文介绍了轴销剪切式称重传感器的结构与特点,受力分析与理论计算。
This article introduces structure, characteristic, stress analysis and theoretical calculation of shaft pin cutting type load cell.
应用推荐